Lowrance Active Imaging 3-IN-1 Installation Manual Download Page 21

Page: 21 / 24

Active Imaging SideScan transducer

Environmental

Operating temperature -15°C to +55°C (+5°F to +131°F)

Storage temperature -30°C to +70°C (-22°F to +158°F)

Physical

Dimensions See

"Dimensions"

on page 18

Cable length 7.6 m (25 ft) or 1.8 m (6 ft)

Mounting options Transom, flush step, and

jackplate mounting

Number of pins 9 pins

Transducer

Output SideScan imaging, DownScan

imaging and temperature

Frequency 455 kHz and 800 kHz

Max depth

•

DownScan: 91 m (300 ft)

•

SideScan: 91 m (300 ft) side
range at 455 kHz, 46 m (150
ft) side range at 800 kHz

Operating speed DownScan and SideScan: 9

knots (10 mph)

Technical specifications

| Active Imaging transducers Installation

Manual

Summary of Contents for Active Imaging 3-IN-1

























Search results

Summary of Contents for Active Imaging 3-IN-1

Reviews:

Related manuals for Active Imaging 3-IN-1

Brands by name

Popular brands

Lowrance Active Imaging 3-IN-1, Installation Manual

Search results

Summary of Contents for Active Imaging 3-IN-1

Reviews:

Related manuals for Active Imaging 3-IN-1

Brands by name

Popular brands