background image

4/11/14 05583F © Inovonics, 2013 - www.inovonics.com

EN1223D/EN1223D-15 EchoStream

®

 Double-

Button Water-Resistant Pendant Transmitter

Installation and Operation Manual

1 Overview

The Inovonics double-button water-resistant pendant transmitter is our 
smallest, lightest, and most versatile pendant.

Note: 

For UL installations, refer to the 

EN4216MR Installation and 

Operation Manual

, the 

EN4232MR Installation and Operation Manual

, or 

the 

EN7285 Installation Instructions.

1.1 Inovonics Wireless Contact Information

If you have any problems with this procedure, contact Inovonics Wireless 
technical services:

• E-mail: [email protected]
• Phone: 1.800.782.2709, option 2

1.2 Transmitter External Components

 Figure 1  

Transmitter external components

1.3 Transmitter Internal Components

 Figure 2  

Transmitter internal components

1.4 What’s In The Carton

• One EchoStream double-button water-resistant pendant transmitter
• One breakaway neck cord
• One beltclip attachment
• Three housing screws
• One frequency band selection jumper
• One CR2450 coin cell battery

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be maintained by professional 

security technicians

• Products are intended for indoor use
• All products should be manually tested weekly (see “Test the 

Transmitter” on page 2)

2.2 Initial Setup

Battery Installation
1.

Remove the rear housing cover to expose the side of the board that 
holds the battery.

Caution: 

Carefully separate the rear housing cover, ensuring the reset 

button plunger assembly does not fall out of the housing (Figure 2).

2.

Slide the battery under the battery holder, ensuring that it is fully 
inserted and that the positive terminal (+) faces up (Figure 2).

Select the Frequency Band

EchoStream products are able to use a range of radio frequencies, and 
must be configured for your geographic area. This product ships with a 
default frequency range of 902-928 MHz for use in North America. If you 

are using the product in North America, skip to step 6; if you are using the 
product in Australia or New Zealand, you will need to configure the 
transmitter.
To configure the transmitter:

3.

Turn the board over to access the side with the frequency band 
selection pins (Figure 2).

4.

Place the frequency band selection jumper on the appropriate 
frequency band selection pins.

• Place the jumper on the left two pins, marked AU, to set the frequency 

range to 915-928 MHz for Australia.

• Place the jumper on the right two pins, marked NZ, to set the 

frequency range to 921-928 MHz for New Zealand.

5.

Seat the board in the housing with the battery side facing the rear 
housing cover. 

6.

Replace the front housing cover.

7.

Insert the three housing screws, tightening them to 1.25 inch-pounds 
torque. 

Note: 

If you do not have a torque driver, tighten to a snug fit, being careful 

not to overtighten.

Note: 

Tighten the housing screws evenly to help ensure a good seal and 

maintain water-resistance.

Caution: 

Over-tightening the housing screws can result in microcracks in 

the plastic, gaps in the gasket material, and/or stripping of the bushing. Any 
of these conditions can compromise the water-resistance of the device.

Register the Transmitter

The transmitter must be registered and supervised. When supervised, the 
transmitter will send check-in message to the receiver or gateway as 
follows:

• EN1223D: every three minutes.
• EN1223D-15: every 15 minutes.

Each transmitter has a unique factory-programmed identification number. 
Refer to the receiver or gateway's installation instructions for details on 
registering and setting up supervision.

8.

When prompted by the receiver or gateway to reset transmitter, press 
the reset button (Figure 1).

Caution: 

The transmitter should be tested after registration to ensure 

operation. See “Test the Transmitter” on page 2.

3 Operate the Transmitter

To send an alarm, press both activation buttons simultaneously for at least 
one second. Alarm signals are transmitted multiple times and are indicated 
by the blinking transmission LED. When the buttons are released, the 
transmitter sends an alarm restoral signal as indicated by another short 
series of blinking transmission LED lights.

3.1 Wear the Transmitter

The pendant transmitter can be worn in three ways:

• Around the neck with neck chain attachment (included)
• On a belt with the beltclip attachment (included)
• On the arm with optional wristband accessory (ACC623S or 

ACC623L, sold separately)

Caution: 

The neck chain included with the pendant transmitter is designed 

with a breakaway feature for user safety. Substitution of a stronger cord or 
chain may result in injury to the wearer.

Note: 

The optional wristband accessory is not part of the UL listing.

3.2 Water Exposure

All EchoStream water-resistant pendants meet IP54 certification standards 
for dust and water ingress protection, ensuring that:

• Ingress of dust particles does not interfere with the satisfactory 

operation of the device

• There is no harmful effect to the device caused by:

-  Vertically dripping water (when device is tilted up to 15° from normal 

position)

-  Spraying water (falling at angles up to 60° from vertical)
-  Splashing water (from any direction)

A

Transmit LED

B

Activation buttons

C

Reset button

A

Frequency band selection 
pins

B

Battery

C

Reset button plunger 
assembly

C

B

A

A

B

C

Reviews: