LOWES EUK60BNK10LRS Manual Download Page 13

13

       

CAUTION:

 The remote control transmitter can be programmed to multiple receivers or fans. 

If this is not desired, turn wall switch off to any other programmable receiver or fan.

OPERATING INSTRUCTIONS

FCC Compliance Notice for Remote Control and LED Light Kit

Modifications not approved by the party responsible for compliance could void the user's authority 
to operate the equipment.

*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:

        *      Reorient or relocate the receiving antenna.
        *      Increase the separation between the equipment and receiver.
        *      Connect the equipment into an outlet on a circuit different from that to which the
 

     receiver is connected.

*      Consult the dealer or an experienced radio/TV technician for help.

Remove screw on the back of remote control 
transmitter in remote pack (O) to remove battery 
cover. Install two AAA batteries (not included).  

Replace battery cover on remote control 
transmitter with screw just removed.

        

WARNING

Choking Hazard

 - Small parts.

Keep battery away from children.

 1. 

(back

side)

1

Battery

Cover

       

CAUTION:

 “DO NOT DISPOSE OF BATTERIES IN FIRE, BATTERIES MAY EXPLODE OR 

LEAK.” - When disposing of household alkaline batteries, it is best to check with your local and 
state recycling or household hazardous waste coordinators concerning the specifics of the 
program in your area. You may also locate a recycling center by calling 1-800-8-BATTERY or 
1-877-2-RECYCLE or visit www.epa.gov/epawaste/index.htm or www.earth911.org for more 
information.

Remote

Control

Transmitter

Battery

Summary of Contents for EUK60BNK10LRS

















Reviews: