manualshive.com logo in svg

Lovato ADXL 0030 600, Instruction Manual

Share
Download
Lovato ADXL 0030 600 Instruction Manual Download Page 16

 

 

         Doc: I456GB06_16.docx                                       29/06/2016

 

p. 16 / 20

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Commands menu 

 

The commands menu is used to perform occasional operations, like resetting measurements, counters, alarms, etc. 

 

If the advanced access password was entered, the commands menu can also be used to perform automatic operations useful for configuring the instrument. 

 

The following table shows the functions which are available with the commands menu divided according to the required access level. 

 

CODE 

CONTROL 

ACCESS LEVEL 

DESCRIPTION 

C01 

MAINTENANCE RESET 

ADVANCED 

Resets the maintenance interval and resets the alarm 

C02 

THERMAL STATUS RESET 

ADVANCED 

Sets the thermal status to 0% 

C03  

START COUNTER RESET 

ADVANCED 

Resets the number of startings counter 

C04 

HOUR METER RESET 

ADVANCED 

Resets the motor's hour meter 

C05 

ENERGY METER RESET 

ADVANCED 

Resets the energy counters 

C06 

LIMITS RESET 

ADVANCED 

Resets LIM variables with memory 

C11 

REPEAT AUTO SET 

USER 

Repeats the AUTOSET wizard 

C12 

SETUP TO DEFAULT 

USER 

Restores the factory default settings 

C13 

BACKUP SETUP 

ADVANCED 

Saves a copy of the setup parameters  

C14 

RESTORE SETUP 

ADVANCED 

Restores a copy of the setup parameters 

C15 

TEST LOW POWER MOTOR 

ADVANCED 

Test with low power motor – Ignores current-related alarms for a bench test 
with low power motors 

 

 
Installation 

 
 
Recommendations 

 

Switch off power to the soft starter every time you need to work on the electrical or mechanical equipment of the system or machine. 

 

A disconnecting device, such as switch disconnector, line contactor, etc.  must always be included to cut off the power supply. 

 

Never use the starter to drive motor power transformers. 

 

Do not install the starter in areas containing flammable gas or explosives. 

 

Do not place the soft starter close to sources of heat. 

 

Do not use an insulating enclosure since they are poor heat conductors. 

 

You can protect the starter's SCR's properly against short circuit only by using ultra-rapid fuses. To select the fuses, refer to the tables on the last pages of this manual. Note that when 

the bypass relay switch is closed (i.e. motor running), the SCR's are protected against short circuit, overload and overvoltage. 

 
Power factor correction 

 

If power factor correction capacitors are to be used, they must be installed upstream of the soft starter, with a contactor and protection fuses. They must be engaged once starting has 

terminated, and disengaged before stopping. The contactor can be controlled with a relay output programmed to “RUN”. 

 

t <45°

t <45°

t <45°

100mm

50mm

50mm

100mm

Summary of Contents for ADXL 0030 600





















Reviews:

No comments

Brands by name

Popular brands

Load more brands