Lorenz FISH PRO HD+ User Manual Download Page 25

Page: 25 / 37

User Manual

Fig. 4.3.1 - The FISH PRO HD

Installation

♦

Fix the FISH PRO HD

to the mounting location using the four screws

(holes diameter 4 mm), see Fig. 4.3.1.

♦

Route the CHART PLOTTER cable to the chart plotter.

♦

Mount the transducer according to the instructions provided with it.

♦

Connect the POWER cable to the battery. Please be advised that the

FISH PRO HD

when not operating will remain in Stand-By mode.

4.3.2 Installing Optional Devices

See the External Connection diagram.

4.4

STATUS LED

There are seven different LED behaviors, representing seven different diag-

nostic conditions. These are described below.

♦

OFF

The FISH PRO HD

is not powered or maintenance/update routines

are running.

♦

ON, CONTINUOUSLY

There is not communication with the chart plotter, and no trans-

ducer is connected.

♦

1 long flash every 2 seconds

A transducer is connected properly, but there is no communication

with the chart plotter.

♦

2 short flashes every 2 seconds or 1 short flash every 2

seconds

The FISH PRO HD

and the transducer are operating properly. This

is the normal behavior when everything is working.

♦

3 short flashes every 2 seconds

The FISH PRO HD

has detected a transducer without transducer ID.

On the chart plotter a warning window is shown, select "IGNORE" and

press [ENTER]: the FISH PRO HD

is working at low power.

♦

4 short flashes every 2 seconds

The FISH PRO HD

has detected a transducer without transducer ID.

On the chart plotter a warning window is shown, select "CANCEL" and

press [ENTER]: the FISH PRO HD

is not sending any signal.

Summary of Contents for FISH PRO HD+






































Search results

Summary of Contents for FISH PRO HD+

Reviews:

Related manuals for FISH PRO HD+

Brands by name

Popular brands

Lorenz FISH PRO HD+, User Manual

Search results

Summary of Contents for FISH PRO HD+

Reviews:

Related manuals for FISH PRO HD+

Brands by name

Popular brands