12
1. Remove the battery door on the back of the sensor.
2. Use the channel switch to set the channel number for the sensor.
3. Insert two (2) AA batteries into the battery compartment according to the +/- polarity labeled in
the compartment.
4. Place the battery door back on the sensor. The sensor will then be in pairing mode and can be
registered to the console within the next few minutes. The transmission status LED will begin to
flash every minute.
NOTE: To change the sensor to a new channel, slide the channel switch to a different channel.
Then, press the RESET button on back of the sensor.
Your console can pair up with one (1) wireless 7-in-1 outdoor sensor and up to seven (7) wireless
indoor sensors. (Only one (1) indoor sensor included.)
1. Insert a screw or hook into the wall.
2. Hang the sensor onto the screw or hook using the wall mounting holder. (Note that the sensor can
also be placed on a table.)
1. Remove the battery door on the rear of the console.
2. Insert a new button battery.
3. Replace the battery door.
NOTE: The backup battery can assist with backing up the time & date, MAX/MIN data, weather
records from the past 24 hours, alert settings, the offset value of weather data, and the
sensor(s) channel history. The built-in memory will backup router and weather server settings.
SETTING UP THE WIRELESS INDOOR HYGRO-THERMO SENSOR
SETTING UP THE WEATHER CONSOLE
INSTALLING THE BATTERIES
PLACING THE WIRELESS INDOOR HYGRO-THERMO SENSOR
INSTALLING THE BACKUP BATTERIES
https://wondery.com/shows/
the-thing-about-pam/#
5
INSTALL WIRELESS INDOOR SENSOR
1. Remove the battery door of the sensor.
2. Use the channel slide switch to set the channel number for the
sensor (e.g. Channel 1)
3. Insert 2 x AA size batteries into the battery compartment and close
the battery door according to the polarity information marked on the
battery compartment.
4. The sensor is in synchronization mode, and can be registered to the
console within the next few minutes. The transmission status LED
will begin to flash every 1 minute.
NOTE:
-If you need to re-assign the sensor channel, slide the channel slide switch to the new channel
position. For the new channel number to be effective, press
[ RESET ]
key on the sensor.
- Avoid placing the sensors in direct sunlight, rain or snow.
-To avoid the sensor/s and console pairing failure during new console setup, please power up
the sensor/s first, and then press
[ RESET ]
key on the main unit (no need on sensors).
PLACING THE WIRELESS INDOOR SENSOR
Place a screw on the wall that you wish to hang the sensor on.
Hang the sensor onto the screw by the wall mounting holder. You
can also place the sensor on a table by itself.
SETUP THE CONSOLE
POWER UP THE CONSOLE
1. Plug the adapter provided to the power jack at the back of the console.
2. Once the console is turned on, all the segments of the LCD will be shown momentarily.
3. The console will automatically enters sensor synchronization mode and AP mode (refer to
SETUP WI-FI CONNECTION
).
NOTE:
If no display appears on the LCD after you plug the adaptor, press
[ RESET ]
key by using a
pointed object.
SYNCHRONIZING WIRELESS 7-IN-1 SENSOR AND INDOOR SENSOR(S)
Immediately after power up, while still in Synchronization mode, the 7-in-1 sensor and Indoor
Sensor can be paired to the console automatically. Once your sensors are paired up, the
sensors' signal strength indicator and weather reading will appear on your console display.
BACKUP BATTERY
Backup batteries are used to keep time-sensitive information on the console’s memory during
power failure. These include:
-
Time & Date, Alarm Time, Max/Min & Past 24 hours weather records, Alert setting values,
Sensor(s) channel history, and Units
5
INSTALL WIRELESS INDOOR SENSOR
1. Remove the battery door of the sensor.
2. Use the channel slide switch to set the channel number for the
sensor (e.g. Channel 1)
3. Insert 2 x AA size batteries into the battery compartment and close
the battery door according to the polarity information marked on the
battery compartment.
4. The sensor is in synchronization mode, and can be registered to the
console within the next few minutes. The transmission status LED
will begin to flash every 1 minute.
NOTE:
-If you need to re-assign the sensor channel, slide the channel slide switch to the new channel
position. For the new channel number to be effective, press
[ RESET ]
key on the sensor.
- Avoid placing the sensors in direct sunlight, rain or snow.
-To avoid the sensor/s and console pairing failure during new console setup, please power up
the sensor/s first, and then press
[ RESET ]
key on the main unit (no need on sensors).
PLACING THE WIRELESS INDOOR SENSOR
Place a screw on the wall that you wish to hang the sensor on.
Hang the sensor onto the screw by the wall mounting holder. You
can also place the sensor on a table by itself.
SETUP THE CONSOLE
POWER UP THE CONSOLE
1. Plug the adapter provided to the power jack at the back of the console.
2. Once the console is turned on, all the segments of the LCD will be shown momentarily.
3. The console will automatically enters sensor synchronization mode and AP mode (refer to
SETUP WI-FI CONNECTION
).
NOTE:
If no display appears on the LCD after you plug the adaptor, press
[ RESET ]
key by using a
pointed object.
SYNCHRONIZING WIRELESS 7-IN-1 SENSOR AND INDOOR SENSOR(S)
Immediately after power up, while still in Synchronization mode, the 7-in-1 sensor and Indoor
Sensor can be paired to the console automatically. Once your sensors are paired up, the
sensors' signal strength indicator and weather reading will appear on your console display.
BACKUP BATTERY
Backup batteries are used to keep time-sensitive information on the console’s memory during
power failure. These include:
-
Time & Date, Alarm Time, Max/Min & Past 24 hours weather records, Alert setting values,
Sensor(s) channel history, and Units
