background image

                 

User’s Information Manual

9

2  

Operating instructions 

(continued)

To Turn Off Gas to Appliance

1. 

Set the thermostat to the OFF position.

2.    Turn off all electric power to the appliance if service is to 

be performed.

3a.    45,000 - 135,000 Btu/hr models, rotate the gas control 

knob on the gas valve clockwise to the “OFF” position.  
Do not force.

3b.   180,000 - 260,000 Btu/hr models, rotate the gas control 

knob on the gas valve clockwise to the line on the 
collar around the knob. Depress the knob and continue 
rotation to the “OFF” position.  Do not force.

 WARNING

Should overheating occur or the gas fail to 
shut off, turn off the external manual gas 
valve to the appliance.

Safety Shutoff Test for Spark 

Ignition Pilot System

1.    Turn “OFF” gas supply to the appliance.

2.    Turn thermostat to highest setting.

3.    Turn electric power “ON”.

4. 

Pump relay pulls in to start pump.

5. 

The ignition will begin sparking at the pilot.

6.    The ignition module will lock out after the trial for 

ignition period.

7.  Immediately call a qualified serviceman or

in 

stall 

er to repair an ignition system that fails to 

lock out and properly shut down burner operation.

8.   After successful completion of the test, re ad just  the 

thermostat to normal setting.

9. Turn 

“ON” 

gas 

supply.

10.    Turn power “OFF” then “ON” to reset ignition module.

11.   If  ignition system fails to operate properly, re 

pair 

work must be performed by a qualified serviceman or 
installer.

Intermittent Pilot Spark Ignition 

System

 WARNING

The ignition module is not repairable. 

 

Any mod i fi ca tion or repairs will invalidate 
the warranty and may create hazardous 
conditions that result in prop er ty damage, 
personal injury, fire, explosion and/or 
toxic gases.  A faulty ignition module must 
be re placed with a new module.

Summary of Contents for 000 BTU/HR













Reviews: