CHAPTER 5: PNEUMATICS
5-7
ECOLOAD S2
6. MAINTENANCE
The pneumatic system should be regularly maintained in order to ensure the system is powered by
qualified compressed air. We recommend the user to check the F.R.L. combination as instructed below
every week.
6.1. Check the condensate collector
The condensate collector is a measure of quality of the compressed air. A qualified air should not produce
any condensate inside the collector.
The F.R.L. combination should never be a replacement of air dryer!!!
The collector has an automatic drain plug. When there is no pressure inside the F.R.L. system, the drain
plug is activated by the spring and the condensate released.
For users which always connect the compressed air, a manual draining is needed. Whenever the
condensate is found inside the collector, drain the condensate by pushing the plug upward and check the
humidity control system.
6.2. Check lubricator
The oil consumption varies with the bar feeder applications. The oil height should not exceed half of the
oil cup height. It is recommended to use oil ISO VG 32 only. When the oil is less than 30%, follow the
procedures below to refill it.
Disconnect the air inlet tube.
Remove the plug and fill the oil up to the position shown on the figure.
For the best performance, the oil should drop once every pusher complete forward/backward
moving cycle. If the working environment is humid or lathe does not installed air filter system users
can drop more. Adjust the amount according to actual production conditions.
Connect the air inlet tube and turn air source on.
Decreasing oil
dribbling
Oil dribbling nozzle
Increasing oil
dribbling
Oil refill plug
Oil level
Summary of Contents for Eco Load S2
