background image

4 (9)

detection of water. The sensor is made from a strip 

of cloth that contains metal threads. If the material 

becomes wet or damp, the leak detector will set off 

an alarm and transmit a signal to the master unit, 

which shuts off the water.

Example of leak detector installation in a kitchen cup-

board.

Loosen the cover on the leak detector by unscrew-

ing the four screws. Install two AA 1.5V alkaline 

batteries if an external power supply or bus com-

munication are not used. Alternatively, an external 

power supply adapter can be connected to a DC 

connector. See under Accessories.

NOTE!

When a leak detector is connected by bus 

communication or an external 5V DC current, 

no batteries should be used.
Only alkaline batteries should be used with 

the product, not rechargeable batteries.

The built-in temperature monitoring can be deac-

tivated by moving the DIP switch to ON. This 

function is normally always activated. If the leak 

detector is connected using bus cable, communi-

cation and power are supplied via the bus cable. 

Connect the bus cable to D and -. The cable should 

be twinned type, 2 x 0.5 mm

2

.

+  D  -

 

D  -

 

Terminal on the leak detector for bus communication.

Place the leak detector at a suitable height from 

the floor so the sensor cable can reach down to its 

location. The detector should be easy to access for 

changing batteries and to reset any alarms that are 

indicated with a sound and diode lights. Secure 

the leak detector with suitable screws. Connect 

the sensor to the leak detector.

Starting the system

Power up the master unit and other units with 

either battery power or an external power source.

Programming

If the system is connected using bus communica-

tion, no programming is required. If the units are 

supplied with battery or external power, wireless 

communication must be established with the mas-

ter unit as below.

Leak detector

To programme the leak detector, simultaneously 

press the Open and Timer keys on the master unit 

for 2 seconds (until radio symbol begins flashing). 

Then press the red button on the underside of the 

leak detector for 2 seconds (until right diode flashes 

green). If programming is successful, the right 

diode will show a green light for a few seconds.

Programming the leak detector.

Installation guide | LK Water Safety System WSS PIR

EN.40.C.9.1911

Summary of Contents for WSS PIR










Reviews: