background image

8 (9)

Technical data

Master unit

Power supply 12V 1A DC. 

Contact for sensor connection: 3.5 mm. 

Radio frequency: 433 MHz, bi-directional. 

2-wire bus communication. 

Temperature measurement: -10 - 55 °C. 

2 LK electric valves can be connected. 

2 LK Pressure Sensors 4-20mA can be connected. 

1 digital input. 

2 alarm outputs, max. resistive load 4A 250V AC. 

3 keys with 6 alarm indicators. 

Dimensions: 162 x 90 x 45 mm

PIR sensor

Power supply 12VDC.

Dimensions 105 x 61 x 44 mm.

Leak detector

Power supply 2 x AA alkaline batteries or 5V 100 

mA DC. 

Contact for sensor connection: 3.5 mm. 

Radio frequency: 433 MHz, bi-directional. 2-wire 

bus communication. 

Temperature measurement: -10 - 55 °C. DIP 

switch to shut off the temperature alarm. 

2 diodes for alarm indication and one buzzer. 

Dimensions: 137 x 62 x 28 mm.

Electric valve 

Pressure range: 0-10 bar. 

Temperature range: 0-80 °C. 

Connection: G15, G20 or G25. 

Power supply: 12V DC. 

Material: stainless steel SS304. 

Cable with snap connector fitted.

     

433 MHz

Comment 

Completely trouble-free operation cannot always 

be guaranteed with the technology available 

today that allows free use of the frequency band. 

Every installation should therefore be tested indi-

vidually. 

Environment 

LK Systems is affiliated with El-Kretsen for collect-

ing and recycling electronics and batteries. Used 

batteries should be sorted as batteries or small bat-

teries and deposited for battery recycling. When 

the system has reached the end of its life, it should 

be sorted as electronics or other electronics and 

deposited with a recycling centre. 

Guarantee 

LK Systems AB is responsible for faults in products 

that appear within two years from the delivery of 

the product to the buyer. If LK is responsible for 

the fault in the product, LK has the right to replace 

the product with either a new or repaired product. 

The liability period for replacement or repair of a 

product or spare part does not exceed the liability 

period for the original product. The seller is not 

responsible for faults resulting from accidents, 

incorrect assembly, incorrect installation, incorrect 

care, abuse or other irregular use. LK Systems AB 

is not liable for any form of loss or damage caused 

by a non-functioning product. Liability is strictly 

limited to replacement of the product. 

System approval 

LK Water Safety System WSS is tested and 

approved in accordance with SINTEF Technical 

Approval No. 20598.

Installation guide | LK Water Safety System WSS PIR

EN.40.C.9.1911

Summary of Contents for WSS PIR










Reviews: