manualshive.com logo in svg

LK Systems ICS-RF8, Assembly Instructions Manual

Share
Download
LK Systems ICS-RF8 Assembly Instructions Manual Download Page 25

LK Floor Heating | Assembly Instructions | LK Room Temperature Control ICS-RF8

25

EN.33.C.104.1012

Error

Description

Action

05

No communication
in the BUS (from
the network).
Taken from the
info.txt file

Check the
connection points

07

Receiver unit is not
numbered (from the
network). Taken
from the info.txt

08

MEM does not
work. U LED lights
red.

Try to mount the LK
ICS MEM Stick
again. U LED lights
green when
functioning
properly.

LK Repeater ICS

 
LK Repeater ICS is used to increase the transmission distance between the LK Room Thermostat ICS RF and
the LK Receiver unit ICS-RF.
The repeater consists of a radio link with receivers and transmitters. A transformer that plugs into a 230V outlet
comes with the repeater. The repeater is placed between the outer thermostat and receiver. Mount the repeater
so that the antenna is vertical. The set-up may contain up to 4 sets of repeaters.

Adaptation of LK Repeater ICS

The repeater is connected as follows:

1. Switch the repeater off (if it is powered up).
2. Press the L key for at least 3 seconds on the receiving device. The L-LED should light green.
3. Connect the repeater to a 230 volt outlet.
4. Wait until the repeater starts flashing orange.
5. Confirm by pressing the L key.

Summary of Contents for ICS-RF8






























Reviews:

No comments

Brands by name

Popular brands

Load more brands