background image

5 (9)

EN.33.C.111.1804

Assembly instructions | LK Electric Boiler - 4,5

Wiring diagram

4,5 kW / 400V 3N~ / 6,5 A

Feed cable: 5 x 1,5 mm²

Protection fuse: 3 x 10A

The boiler operates in two power steps, 2,25 and 

4,5 kW. 

At 2,25 kW, only phases L1 and L2 (5, 6 A) are 

loaded.

1 3

X

L3 L2 L1

P

N

N N

N

N

N

11

21

31

12

22
24
32

42

32

22

41

31

21

L4

L3

L1

T4

T3

T2

L1

T1

80°C

10- 60°C

T

T

1

2

3

4.5 kW

ALARM

OPERATION

A1

A2

N

N

11

1

2

3

4

5

6

7

8

9

10

12

Delivery configuration, 4,5 kW / 400V 3N~ / 6,5 A

1.  External switching
2.  Jumper, for 1,5 and 3kW connection
3.  Connection terminal
4.  Suppressor capacitor
5.  Circulation pump
6.  Overheating (maximum safe temperature) 

protection

7.  Thermostat 
8.  Electric cartridge
9.  Control switches
10. Alarm indication, overheating (maximum 

safe temperature) protection triggered

11. On/off indicating light, goes on when vol-

tage is supplied to the boiler

12. Contacts

External switching/room thermostat

The boiler can be blocked by external equipment, 

e.g. room thermostat with potential-free opening 

contact suitable for 230 V/10A. Connection is car-

ried out at terminals 1 & 3 on the boiler connection 

terminal.

1 3

X

L3 L2 L1

P

N N

Note! If the boiler is wired to supply which is fused 

higher than 10 A the enclosed automatic fuse must be 

used. Connection wires and the DIN-rail with its termi-

nal blocks must be installed as shown below.

10 A

Summary of Contents for Electric Boiler-4.5










Reviews: