background image

8 (9)

EN.33.C.111.1804

Assembly instructions | LK Electric Boiler - 4,5

Troubleshooting

Intervention in the boiler which requires the use of tools should be carried out by an authorized electrician. 

Begin all troubleshooting tasks by looking at the status indicators, see the 

Control panel

 section.

Error

Possible cause

Measures

On/off indication 

is off, there is no 

heat in the heating 

system.

The electric boiler is currentless.

Check the fuses.

Circuits switched off.

Check that the main and control switches are on.

The electric boiler is blocked externally.

Check if the boiler is blocked by external switching/room ther-

mostat.

Alarm light is on.

Overheating (maximum safe temperature) 

protection is triggered.

If the overheating (maximum safe temperature) protection goes 

off, the function should be controlled at the circulation pump and 

valves. During resetting the button on the overheating (maxi-

mum safe temperature) protection is pushed in when the boiler 

temperature falls below 65°C (push the button hard for reset).

No or insufficient 

heat.

Thermostatic valves on the heating system or 

boiler thermostat set at too low temperature.

Inspect and adjust.

Faulty adjustment of bypass valve.

Inspect and adjust.

Group fuses for 

boiler are triggered.

The electric cartridge is broken.

Inspect the electric cartridge by testing it in isolation. Measure 

between the outward side on the contacts, and earth. 

Inform the installer!

Intervention in the boiler, which requires the use of tools, must only be carried out under the supervision 

of an authorized installer!

Drawings

9

14

10

6

5

7

1

11

8

12

3

2

4

2

13

1.  Cable bushes 
2.  Automatic bleeding valve 
3.  Expansion vessel 
4.  Sensor clip, thermometer bulb 
5.  Boiler vessel of stainless 

steel with electric cartridge, 

insulated 

6.  Circulation pump 
7.  Electric-shock protection over 

electric cartridge cable con-

nections 

8.  Bypass with shut-off valves 
9.  Flow pipe, ¾” male thread 
10.  Return connection, ¾” male 

thread 

11.  Collection vessel, waster 

water from safety valve 

12.  Safety valve 
13.  Electric-shock protection 
14.  Knockouts for cables, where 

these come from the wall

Summary of Contents for Electric Boiler-4.5










Reviews: