Installing the Living Water Essentials U7
NOTE:
You need to remove the lock collar from the quick connect fitting before you can install the tubing. Reattach the lock collar
after inserting the tube.
• Connect length of 3/8 inch tubing to the OUT WATER quick connect on the Living Water Essentials faucet. Connect
opposite end to the INLET on the u7 unit.
• Take the gray ALKALINE flexible tubing from the Living Water Essentials faucet and connect to the ALKALINE quick
connect on the u7 unit.
• Take the white ACIDIC flexible tubing from the Living Water Essentials faucet and connect to the ACIDIC quick
connect on the u7 unit.
NOTE:
Insert water supply and drain lines into the quick connects until they will not go in any further. Give each line a slight tug at
the point of connection to make sure the lines are properly connected and that they do not slip out. This step will ensure proper
installation and avoid possible leaks from improperly installed lines.
• Take the RS232 Connection from the Living Water Essentials faucet and connect to the CONNECTOR on the back of
the u7 unit. Tighten securely.
• Verify the power selector switch is in the proper position for your power supply (115 volt vs. 220 volt). Attach power
cord.
• Set unit into place under cabinet, making sure none of the flexible tubes are kinked.
• Open the water supply valve, checking for leaks.
• Plug in unit to power supply.
• Turn on power switch on front of u7 unit.
10
11
G
O P E R AT I O N
NOTE:
Please begin drinking alkaline water gradually as it is detoxifying. For example, drink 16 oz. of Level 1 water for several days,
gradually increasing the amount you consume to your full daily amount of water. Increase one level each week until you are drinking
your full daily amount of water on Level 4 (highest pH level). Following this gradual procedure will minimize unpleasant effects of
detoxification, such as cold or flu-like symptoms, headaches, rashes, diarrhea and/or nausea. You may notice differences in bowel
habits during the first days at each pH level. Urine frequency may increase and color may darken as more water is consumed and your
body detoxifies. Eventually the color decreases as your body adjusts to the cleansing. If detoxification symptoms become
uncomfortable, it is suggested that you decrease to a lower level alkaline water until these symptoms subside and gradually build up
again to higher levels.
The upper spout on the Living Water Essentials is the selected pH level. The lower spout is the drain water.
Acidic:
Acidic water is a pH level of 5.0-6.5. This water is an astringent and is excellent for cleaning.
This is not drinking water.
Filtered Water:
Neutral water is a pH level of 7.0. This water should be used when taking medicines or with
baby formula.
Alkaline L:
Alkaline L is a pH level of 8.0-8.5. Begin drinking water from this level for the first week,
gradually increasing your consumption.
Alkaline M:
Alkaline M is a pH level of 8.5-9.0. Drink water from this level once you are adjusted to
Alkaline L, gradually increasing your consumption.
Alkaline H:
Alkaline H is a pH level of 9.0-9.5. Drink water from this level once you are adjusted to
Alkaline M, gradually increasing your consumption. This is the ideal setting once the body has
adjusted to alkaline water. In the fourth week and thereafter, use this water for drinking,
cooking, coffee and tea.
NOTE:
pH is measured on a scale from 0 to 14.0 with 7.0 pH being neutral; the water being neither alkaline nor acidic. The total pH
will be 14. For example, if the U7 unit is producing alkaline pH 9.5 water (delivered at the upper spout), the acidic water being
delivered at the lower spout will have a pH of approximately 4.5 acidic.
IMPORTANT:
DO NOT drink any of the following water types:
•
ANY acidic water
•
High pH alkaline water (above 10.0 pH)
•
Water produced during the auto flush (electrode cleaning) process.
•
When no pH value is displayed on the LED display.
•
When the u7 unit has not been used for more than two days, let water run for 30 seconds before consuming.
Acidic Tubing
Alkaline Tubing
Out Water
Quick
Connect
Feed
Water
Quick
Connect
RS232
Connection
After Installation
• Let the water run for 2 minutes through the faucet to remove the air from the lines.