![background image](http://html1.mh-extra.com/html/little-wonder/e-system/e-system_owners-manual-and-safety-instructions_1929718005.webp)
4
18. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it
will operate properly and perform its intended function.
Check for alignment of moving parts, free running of
moving parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorised service centre unless otherwise
indicated in this instruction manual. Have defective
switches replaced by an authorised service facility. Do not
use the tool if the switch does not turn it on and off.
Don’t
operate the machine with a damaged or excessively
worn cutting device.
19. The use of any accessory or attachment, other than those
recommended in this instruction manual, may present a
risk of personal injury.
20. Have your tool repaired by a qualified person.
This electric tool conforms to relevant safety requirements.
Repairs should only be carried out by qualified persons
using original spare parts, otherwise this may result in
considerable danger to the user.
21. Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
22. Work only in daylight or in good artificial light.
23. Keep all guards attached at all times when unit is operated.
24. Always use the shoulder strap.
Adjust the strap for comfort before starting the engine.
25. Secure unit during transport to prevent damage or injury.
26.
Machine should not be used in any position that causes
any part to come within 3 metres of overhead electrical
lines.
Always be aware of overhead power lines.
27.
Always
keep a firm grip on both handles when motor is
running: one hand grasps the front “loop” handle while the
other hand grasps the rear handle. Severe injuries can
result if you try to use this machine with only one hand or
with an insecure grip.
28.
Thoroughly
inspect the area where equipment is to be
used and removed all objects, which can be thrown by the
machine.
29.
Always
keep area clear of children, pets, and bystanders.
30.
Always
inspect your unit before each use and ensure that
all handles, guards and fasteners are secure, operating, and
in place. Be sure that all electrical cords are not damaged
or broken.
31.
Always
maintain and examine your attachments with care.
Follow maintenance instructions given in manual.
32.
Don’t
attempt to repair any part of the extended reach
E System. Have repairs made by a qualified repairman.
See that only original “Mantis” parts are used.
33. Maintain a firm footing and good balance, do not
overreach while trimming. Before you start to trim, check
the work area for obstacles that might cause you to lose
your footing, balance or control of the machine. While
operating the machine always be sure of a safe and secure
operating position and be sure of your footing on slopes.
WARNING – DANGER
LITTLE WONDER WILL NOT BE RESPONSIBLE
FOR THE FAILURE OF CUTTING DEVICES OR
ACCESSORIES THAT HAVE NOT BEEN TESTED
AND APPROVED FOR USE WITH THIS UNIT.
USE ONLY MANUFACTURER-RECOMMENDED
REPLACEMENT PARTS.
WARNING – DANGER
IMPROPER ASSEMBLY OF THIS EQUIPMENT
CAN RESULT IN SERIOUS INJURY. MAKE SURE
TO FOLLOW ALL INSTRUCTIONS CAREFULLY.
IF YOU HAVE ANY QUESTIONS, CONTACT YOUR
LOCAL AUTHORISED MANTIS DEALER.
34. Always disconnect power cord from power source:
a. Before cleaning blockages.
b. Before checking, cleaning or working on the
cutting portion of the unit.
c. After striking a foreign object: inspect the cutting
part for damage and make repairs before restarting
and operating the unit.
d. If machine starts to vibrate abnormally (check
immediately).
e. Whenever you leave the unit.
35. Securing the extension cord.
Bend the extension
cord about 40 cm from
the plug end. Push that
bend through the
oblong opening, then
loop the bend under the
cord retaining clips as
shown. This will
prevent the extension
cord from detaching
from the line
trimmer plug.