Lithonia Lighting RSX1 LED P4 Manual Download

Page: 9 / 16

Installation Instructions
RSX LED

RSX INTEGRAL SLIPFITTER (KNUCKLE) INSTALLATION ON VERTICAL TENONS (+/- 5 °)

Note: Luminaire can be tilted up to 90 degrees (maximum) above horizontal.

Tools Required:

Allen wrench: 9/64”, 5/16“, 3/8”

Maximum tenon/pole diameter: 2” schedule 40 pipe (2-3/8” OD)

This luminaire is pre-wired with UL listed supply wire leads. It is not necessary to access fixture housing to install or

wire the luminaire.

1. Remove the two (2) 8-32 splice access cover fasteners from knuckle assembly, remove the splice access cover, and

pull supply wire leads from knuckle cavity (See Figure 12a)

2. Slip luminaire knuckle fitter over 2-3/8”Ø pole tenon and evenly tighten the six (6) 3/8-16 UNC knuckle tenon set

screws to 23-27 ft-lbs, while maintaining the correct position of the luminaire.

3. Cut and splice the wires. Recommended cut length is 6" for wires for ease of splicing and securing in the knuckle.

(See Figure 12b)

4. Make all wiring connections via the supplied wire leads in accordance with NEC and local codes.

5. Push all fixture and supply wires completely within the knuckle cavity and replace the splice access cover, gasket,

and two (2) 8-32 splice access cover fasteners.

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Part Number: IN-379 Rev F

Revision Date: 11/19/18

Splice Access

Cover Bolts

Pole Tenon

Knuckle Tenon

Set Bolts

Figure 12a

Figure 12b

Splice Access

Cover

Summary of Contents for RSX1 LED P4

















Search results

Summary of Contents for RSX1 LED P4

Reviews:

Related manuals for RSX1 LED P4

Brands by name

Popular brands

Lithonia Lighting RSX1 LED P4, Manual

Search results

Summary of Contents for RSX1 LED P4

Reviews:

Related manuals for RSX1 LED P4

Brands by name

Popular brands