Lithe Audio 06300 Installation Manual Download Page 2

2

1

NOTE: Read the entire instruction manual before you start installation and assembly.

Component Checklist

WARNING

IMPORTANT: 

Ensure that you have received all parts according to the component checklist prior to installation.

                                 If any parts are missing or faulty, telephone your local distributor for a replacement.

Package M

adapter bracket (x2)

D

Package W

ST6.3x55  (x5)

W-A

concrete anchor (x5)

W-B

D6 washer (x3)

W-C

motorized wall mount (x1)

A

M5x14 (x4)

M-A

M6x14 (x4)

M-B

washer (x4)

M-F

M8x20 (x4)

M-C

big spacer (x4)

M-H

M6x30 (x4)

M-D

M8x30 (x4)

M-E

small spacer (x8)

M-G

cable clip (x2)

C

wall template (x1)

B

remote control (x1)

F

power supply (x1)

G

• Do not begin the installation until you have read and understood all the instructions 

 

 and warnings contained in this installation sheet. If you have any questions 

  

r

egarding any of the instructions or warnings, please contact your local distributor.

• T

hi

s mounting bracket was designed to be installed and utilised ONLY as 

  spe

c

ified in this manual. Improper installation of this product may cause damage 

  or se

r

ious injury.

• This

 p

roduct should only be installed by someone with good mechanical ability 

   who ha

s

 basic building experience and fully understands this manual. 

• Make su

re

 that the supporting surface will safely support the combined weight of 

  the equipm

e

nt and all attached hardware and components.

• If mountin

to wood wall studs, make sure that mounting screws are anchored 

  into the cent

e

r of the studs. The use of a stud finder is highly recommended.

• Always use an

 a

ssistant or mechanical lifting equipment to safely lift and position 

  the equipment.

·

 Tighten screws f

ir

mly, but do not over tighten. Over tightening can cause damage

  to the items, This

 

greatly reduces their holding power.

• This product is in

te

nded for indoor use only. Using this product outdoors could 

  lead to product failu

r

e and personal injury.

• Please do not disassemble or change the electronic components of the product 
  without authorization.

IR receiver (x1)

E

bubble level (x1)

H

Summary of Contents for 06300









Reviews: