Lithe Audio 06300 Installation Manual Download Page 1

15

CAUTION:

 

DO NOT EXCEED 

RATED LISTED WEIGHT. SERIOUS 

INJURY OR PROPERTY DAMAGE 

MAY OCCUR!

60"

MAX

200x200

300x300

400x200

400x400

40kg

(88lbs)

RATED

OK

OK

  LEARN MODE instructions as shown below:

  

STEP1: Press and hold       for 5 seconds until LED light on the matched remote control stays on, and 

  then press        . The buzzer will sound once, the red LED light on the IR receiver will stay on, then the 
  LEARN MODE will be entered.

  STEP2: If LEARN        , please press         on the matched remote control until the buzzer sounds twice, 
  the red LED light on the IR receiver will change from being steady to a slow flash.

  STEP3: Aim the TV remote at the IR receiver, and press the button on the TV remote that you need to set as 
  the function of         button until the buzzer sounds three times. the red LED light on the IR receiver will 
  change from slow flash to a fast flash.

  STEP4: Press       button on the matched remote control until the buzzer sounds four times. The 
  red LED light on the IR receiver will turn off.        button will be LEARNED successfully. If the buzzer only 
  sounds once, then a LEARN failure.(The TV remote won’t support the LEARNING function).

(Please follow step1 through step4 in turn if the user need to LEARN more buttons)

Learn “Power” button on the TV remote: 
Press and hold        for 5 seconds until LED light on the matched remote control stays on , and then press       .
The buzzer will sound once, the red LED light on the IR receiver will stay on, then press and hold            button 
on the matched remote control until the buzzer sounds twice, then release the            button. The red LED 
light on the IR receiver will change from being steady to a slow flash.
Aim the TV remote at the IR receiver, and press “Power” button. The buzzer will sound three times. The red
LED light on the IR receiver will

 

change from slow flash to a fast flash. Press       button on the matched

remote control until the buzzer sounds four times. The red LED light on the IR receiver will turn off. “Power” 
button will be LEARNED successfully. If press “power” button, the TV wall mount will automatically reset.           

Note: When there is no activity for over 20 seconds in any step .TV remote will automatically exit from the 
LEARN MODE.

Maintenance

•  Check that the bracket is secure and safe to use at regular intervals(at least every three months).   

•  Please contact your distributor if you have any questions.

OK

OK

40kg

(88lbs)

RATED

INSTALLATION MANUAL

REMOTE CONTROL MOTORIZED 

90

O

 WALL MOUNT 32-60"

Summary of Contents for 06300









Reviews: