manualshive.com logo in svg

Lippert Components OneControl X1, Oem Installation Manual

Share
Download
Lippert Components OneControl X1 Oem Installation Manual Download Page 2

Rev: 08.31.20

Page 2

CCD-0002697

TABLE OF CONTENTS

Introduction

 

2

Safety

 

3

Resources Required

 

3

Installation

 

4

Wiring

 

5

Configuring Inputs, Outputs

 

6

Latching Relays 

7

Reverse Polarity Outputs 

13

Saving Configuration 

18

Loading Configuration 

19

Introduction

The OneControl X1 Control Board will primarily be operated by a phone app utilizing a Bluetooth 

connection. Users can access and adjust a system via a touchscreen icon. If the trailer already has 

a OneControl Touch Panel, then the controller can be tied into the OCTP by CAN bus harness. The 

configurator kit supplied to OEMs must be used to program the configurable inputs and the latching and 

reversing outputs.

For information on the assembly or individual components of this product, please visit:

https://support.lci1.com/electronics-support-onecontrol-wireless-formerly-myrvreg

 .

NOTE: 

Images used in this document are for reference only when assembling, installing and/or operating 

this product. Actual appearance of provided and/or purchased parts and assemblies may differ.

Summary of Contents for OneControl X1





















Reviews:

No comments

Brands by name

Popular brands

Load more brands