Lippert Components OneControl Hotspot Installation Manual Download Page 2

Rev: 01.15.20

Page 2

CCD-0002221

TABLE OF CONTENTS

Introduction

 

2

Safety

 

2

Resources Required

 

3

Preparation

 

3

Installation

 

3

Notes

 

9

The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause death 

or serious personal injury if not performed safely and within the parameters set forth in this manual. 

Failure to follow instructions provided in this manual may result in serious personal injury and/or 

severe product and property damage, including voiding of the component warranty.

Unit MUST be supported per manufacturer's recommendations before working underneath. Failure 

to do so may result in death or serious personal injury.

Always wear eye protection when performing service, maintenance or installation procedures. 

Other safety equipment to consider would be hearing protection, gloves and possibly a full face 

shield, depending on the nature of the task.

The "CAUTION" symbol above is a sign that a procedure has a safety risk involved and may cause 

personal injury, product or unit damage if not performed safely and within the parameters set forth 

in this manual.

Introduction

This document provides instructions for the installation of an OneControl Hotspot

TM

 prep kit. The installed 

kit is intended as an optional upgrade for RV owners. 

Safety

Read and understand all instructions before installing or operating this product. Adhere to all safety labels.

This manual provides general instructions. Many variables can change the circumstances of the instructions, 

i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This 

manual cannot begin to plot out instructions for every possibility, but provides the general instructions, 

as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the 

provided instructions may result in death, serious personal injury, severe product and/or property damage.

For information on the assembly or individual components of this product, please visit 

https://support.lci1.com/electronics

NOTE: 

Images used in this document are for reference only when assembling, installing and/or operating 

this product. Actual appearance of provided and/or purchased parts and assemblies may differ.

Summary of Contents for OneControl Hotspot











Reviews: