Linkam Scientific Instruments CSS450 User Manual Download Page 5

 

Handling Liquid Nitrogen 

To cool samples below room temperature a CSS-LNP95 liquid nitrogen pump system is required.  Always use 
liquid nitrogen in a well ventilated room as there is a danger of asphyxiation. 
Refer to your health and safety officer regarding instructions on how to handle liquid nitrogen safely and ensure 
that you have the correct safety equipment including gloves and safety goggles. 

 
Filling the Dewar 

Fill the Dewar approximately 2/3 full and replace the lid with the siphon attached, but 

do not fasten the catches. 

Wait for the liquid nitrogen to stop bubbling before fastening. 
When the lid is removed always ensure you place it with the black capillary tube pointing upwards. It is easily 
damaged or creased which will impair N

2

 flow and the performance of the system. 

 
Equipment Maintenance 

The equipment does not require any regular maintenance.  Contact Linkam should you require any maintenance. 
Before  cleaning  the  case  or  front  panel  of  the  equipment,  remove  the  mains  cord  from  the  mains  
outlet.  Use a small quantity of isopropyl alcohol (IPA) on a soft cloth and gently wipe the surface.   

 

Informations de sécurité 

 
Note importante 

Veuillez vérifier que votre appareil Linkam n'a pas été endommagé pendant le transport.  
S'il présente une trace quelconque d'endommagement aux éléments électriques : 
 

ne raccordez pas le cordon d'alimentation et n'allumez pas l'appareil. 

  

Contactez Linkam Scientific Instruments Ltd ou son distributeur désigné immédiatement. Votre garantie pourrait 
être  réduite  si  Linkam  n'est  pas  informée  de  tout  dommage  causé  par  le  transport  dans  les  7  jours  ouvrables  
suivant la livraison. 
  

Exigences en matière de sécurité d'utilisation 

1.  Lisez ce guide intégralement avant d'utiliser l'appareil. Conservez ces instructions pour un usage ultérieur. 
2.  Suivez  toutes  les  mises  en  garde  et  instructions  marquées  sur toute  pièce  de  votre  appareil,  ou  figurant 

dans les manuels. 

3.  Si pour une quelconque raison le fusible secteur doit être remplacé, il faut le remplacer par un fusible du 

même  type  et  avec  les  mêmes  caractéristiques  nominales  que  celles  indiquées  dans  les  caractéristiques 
nominales de l'appareil. 

4.  Pour prévenir l'électrocution, n'enlevez pas le couvercle de l'appareil. 
5.  N'utilisez  jamais  l'appareil  si  le  cordon  d'alimentation  a  été  endommagé.  Ne  laissez  pas  d'objets  lourds 

appuyés sur le cordon d'alimentation. Ne posez jamais le cordon d'alimentation sur le sol. 

6.  Le secteur cordon est la déconnexion globale et doit rester accessible. 
7.  Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la protection fournie par l'équipe-

ment peut être altérée. 

8.  N'obstruez aucun des orifices de ventilation. N'essayez pas d'insérer quoi que ce soit dans ces ouvertures. 

Prévoyez un espace de ventilation adéquat d'au moins 75 mm autour de l'appareil. 

9.  N'exposez  pas  l'appareil  à  l'eau.  Si  pour  une  quelconque  raison  l'appareil  est  mouillé,  retirez  le  cordon 

d'alimentation de la prise de courant et contactez le support technique de Linkam. 

10.  L'appareil n'est pas destiné à un usage à l'extérieur. 
11.  Chaque produit est équipé d'une fiche d'alimentation mise à la terre ou d'un cordon d'alimentation avec 3 

fils  à  extrémité  libre.  La  fiche  ne  s'insère  que  dans  une  prise  de  courant  mise  à  la  terre.  Le  cordon  
d'alimentation à extrémités libres doit être raccordé à une prise de courant à 3 fils correctement mise à la 
terre. N'empêchez pas le fonctionnement de la fiche mise à la terre. 

 

   Les cordons d'alimentation à extrémité libre suivent les codes couleur suivants : 

 
   

 

Couleur

  

 

Fonction

 

   

 

Marron   

 

conducteur de phase 

   

 

Bleu 

 

 

conducteur neutre 

   

 

Vert/jaune   

mise à la terre 

Summary of Contents for CSS450













































Reviews: