manualshive.com logo in svg

LINET LATERA, Instructions For Use And Technical Description, Page: 49 / 54

Share
Download
LINET LATERA Instructions For Use And Technical Description Download Page 49

D9U001L20-0101_04

           

           49

Cleaning agents

LINET® recommends the following cleaning agents:

Cleaning Agents

Manufacturer

Mikrozid, Terralin Protect, Thermosept

Schülke & Mayr

Bacillol AF, Bacillol Rasant, Dismozon Pur, Microbac Forte, 

Neodisher Dekonta

BODE Chemie

Lysoformin 3000, Lysoform Spezial

LYSOFORM

Incidin plus, Incidin rapid

Ecolab

Perform, TPH protect, 

Schülke

16.1  Preparing for Cleaning

Prepare for cleaning as follows:

► 

Put the mattress platform in the highest position.

► 

Adjust the back and thighrests so that the reverse sides are accessible.

► 

Disable the function buttons on the control elements using the Attendant Control Panel.

► 

Disable the foot controls using the Attendant Control Panel.

► 

Disconnect the bed from the mains.

► 

Move the bed to the location where it will be cleaned.

► 

Lock the brakes on the bed.

16.2  Cleaning

16.2.1 Daily Cleaning

Clean the following bed parts:

► 

All of the control elements for adjusting the bed

► 

All handles

► 

Back and calfrest handles

► 

CPR release handle

► 

Head and foot boards including aluminium columns and crossbars under the boards

► 

Siderails (in highest position)

► 

Freely accessible mattress surface

► 

Accessory rails

16.2.2 Cleaning before Changing Patients

Clean the following bed parts:

► 

All of the control elements for adjusting the bed

► 

All handles

► 

Back and calfrest handles

► 

CPR release handle

► 

Head and foot boards including aluminium columns and crossbars under the boards

► 

Siderails (in highest position)

► 

Freely accessible mattress surface

► 

Accessory rails

► 

All plastic mattress platform covers

► 

Plastic undercarriage covers

► 

Telescopic columns

► 

Mattress on all sides

► 

Freely accessible metal parts on the mattress platform

► 

Cable ducts

► 

Lifting pole sleeve fitting

► 

Infusion stand sleeve fitting

► 

Bumpers

► 

Castors

► 

Brakes

Summary of Contents for LATERA























































Reviews:

No comments