LTM9004
7
9004fa
For more information
www.linear.com/LTM9004
power requireMenTs
The
l
denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at T
A
= 25°C. Unless otherwise noted, V
CC1
= V
CC2
= 5V, V
DD
= OV
DD
= 3V. V
CC3
= 3V (LTM9004-
AC, LTM9004-AD), V
CC3
= 5V (LTM9004-AA, LTM9004-AB) (Note 3)
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
All voltage values are with respect to ground with GND and OGND
wired together (unless otherwise noted).
Note 3:
f
SAMPLE
= 125MHz, CLKI = CLKQ unless otherwise noted.
Note 4:
Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 5:
DC offset voltage is defined as the DC voltage corresponding to
the output code with LO signal applied, but no RF signal.
Note 6:
Guaranteed by design, not subject to test.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
f
S
Sampling Frequency
l
1
125
MHz
t
L
CLK Low Time
Duty Cycle Stabilizer Off (Note 6)
Duty Cycle Stabilizer Off (Note 6)
l
l
3.8
3
4
4
500
500
ns
ns
t
H
CLK High Time
Duty Cycle Stabilizer Off (Note 6)
Duty Cycle Stabilizer Off (Note 6)
l
l
3.8
3
4
4
500
500
ns
ns
t
JITTER
Sample-and-Hold Acquisition Delay Time Jitter
0.2
ps
RMS
t
AP
Sample-and-Hold Aperture Delay
0
ns
t
D
CLK to DATA delay
C
L
= 5pF (Note 6)
l
1.4
2.7
5.4
ns
DATA to CLKOUT Skew
(t
D
- t
C
) (Note 6)
l
–0.6
0
0.6
ns
t
C
MUX to DATA Delay
C
L
= 5pF (Note 6)
l
1.4
2.7
5.4
ns
DATA Access Time After
OE
↓
C
L
= 5pF (Note 6)
l
4.3
10
ns
BUS Relinquish Time
(Note 6)
l
3.3
8.5
ns
Pipeline Latency
5
Cycles
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
P
D(SLEEP)
Sleep Power
MIXENABLE = AMPxENABLE = 0V,
ADCSHDN = 3V,
OE
= 3V, No CLK
7
mW
P
D(NAP)
Nap Mode Power
MIXENABLE = AMPxENABLE = 0V,
ADCSHDN = 3V,
OE
= 0V, No CLK
33
mW
P
D(TOTAL)
Total Power Dissipation
LTM9004-AA, LTM9004_AB,
MIXENABLE = AMP1ENABLE =
AMP2ENABLE = 5V, ADCSHDN = 0V, f
SAMPLE
= MAX
1.83
W
LTM9004-AC, LTM9004-AD
MIXENABLE = AMP1ENABLE = 5V,
AMP2ENABLE = 3V, ADCSHDN = 0V, f
SAMPLE
= MAX
1.83
W
TiMing characTerisTics
The
l
denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at T
A
= 25°C. Unless otherwise noted, V
CC1
= V
CC2
= 5V, V
DD
= OV
DD
= 3V. V
CC3
= 3V (LTM9004-
AC, LTM9004-AD), V
CC3
= 5V (LTM9004-AA, LTM9004-AB)
