background image

9

dc2228af

DEMO MANUAL DC2228A

Dc2228a control tool

4. Apply power from either a 24V power supply or PoE 

power sourcing equipment.

5. Start the Control Tool software.
6. Enter the DC2228A communication settings (Figure 8a 

and 8b). Using the default address:

  IP address = 192.168.10.150 

 

Port = 7

  NOTE: The default IP address can be changed using 

the procedure given in the section 

One Time DC2228A 

configuration to change the fixed IP address

.

7. Connect the Control Tool to the DC2228A using the 

green “Connect” button (Figure 8c and 8d).

IO-Link Operation

To operate a connected device that’s been configured for 

IO-Link operation (Figure 9):
1. Click the “Power ON” button to supply power to the 

device.

2. Click the “IO-Link” button to begin communication.
3.  Operate IO-Link device. For a typical sensor this involves 

monitoring process data and events.

4. Click the “Inactive” and “Power OFF” buttons when 

done.

Digital Input Operation

To operate in DI mode (Figure 10), for receiving data from 

a device connected to the C/Q line:
1. If an IODD file has been associated with the port, 

remove it using 

Select device 

 Exit and not select

When powered, the connected device will now run in 

Standard IO (SIO) mode.

2.  Click the “Power ON” button to supply power to the device.
3. Click the “DI” button. The Raw Process Data In field 

will monitor the digital state at the C/Q pin.

4. In the case of a DC2227A device, the C/Q state can be 

changed by interacting with its light sensor.

5.  Click the “Inactive” and “Power OFF” buttons when done.

Digital Output Operation

To operate in DO mode (Figure 11), for switching the C/Q 

line as a Standard IO (SIO) output:
1. If an IODD file has been associated with the port, 

remove it using 

Select device

 

 

Exit and not select

When powered, the connected device will now run in 

Standard IO (SIO) mode.

2. Consider whether the connected device will tolerate a 

C/Q driver conflict. If conflicts occur, master C/Q over-

current events could be triggered (see 

Fault Conditions

 

section). If connected to a DC2227A, be aware that the 

device output state in SIO mode is determined by its 

light sensor. The DC2228A and DC2227A won’t damage 

each other. Other devices could be stronger or weaker 

than the DC2228A, and might not tolerate a conflict.

3.  Click the “Power ON” button to supply power to the device. 
4. Click the “DO” button and “OK” the confirmation mes-

sage. 

5. Click the “High” or “Low” radio buttons to switch the 

C/Q state.

6. Click the “Inactive” and “Power OFF” buttons when 

done.

Fault Conditions

If the Control Tool detects a fault on any port, it reports, in 

red, a Master PHY event at the bottom of the main window. 

The operator may query faults using the 

Master settings 

 

Check PHY events

 pull-down menu. After fixing the 

underlying condition, the operator may clear faults using 

the same pull-down menu.

Software License and Renewal

The Control Tool license is valid for 10000 minutes of 

cumulative operation. Unlimited free renewals, as well as 

an unlimited license, are available. To renew the license:
1.  Get the hardware ID using 

Tools

 

 

License key manager

 

and clicking the “Export hardware ID” button.

Summary of Contents for LTC2874





















Reviews: