3
/14
Flexible wall
EI 60 S
(300 Pa)
EI 30 S
(300 Pa)
EI 60 S Installation remote from the vertical light wall hole Ø+30
Wall minimum thickness 95 mm
Wall rock wool density up to 35 kg/m³ (optional)
Studs made of steel or timber
mortar or plaster putty or rock wool 35 kg/m³ and acrilic sealant sealing
ve (i
↔
o)
D/W
Ø
min 100
max 400
Ø
min 100
max 400
EI 60 S Installation remote from the vertical light wall hole Ø+10
Wall minimum thickness 95 mm
Wall rock wool density up tp 35 kg/m³ (optional)
Studs made of steel or timber
Acrilic sealant sealing
ve (i
↔
o)
D
Ø
min 100
max 400
Ø
min 100
max 400
Floor
EI 60 S
(300 Pa)
EI 30 S
(300 Pa)
Installations remote from the floor
Floor minimum thickness 100 mm
Floor minimum density 550 kg/m³
Mortar or plaster putty or rock wool 35 kg/m³ sealing
ho (i
↔
o)
D/W
Ø
min 100
max 400
Ø
min 100
max 400
Ø is the minimum and maximum nominal diameter of fire dampers in mm
ve
Vertical installation
ho
Horizontal installation
(i
↔
o) Origin of fire irrelevant
Pa
Pascal of depression
E Integrity
I
Thermal insulation
S
Smoke seal
W
Wet method sealing
D
Dry method sealing
Cert. N° 1812-CPR-1639
Mechanism type
Manual and compact manual
Not available
Belimo motorized version
1. Blade locking lever
2. Position indicator
3. Hex key for manual opening
4. Manual closing switch
Blade closing mode
Automatic closing with thermal fuse.
The control mechanism has a thermosensitive element that automa-
tically closes the blade when the temperature in the duct or in the
room exceeds 72°C (or 95°C for the 95°C version).
To close the damper when the motor is connected, press the switch
on the temperature sensor or cut off the power supply.
Blade opening mode
Make sure that the damper is open before the ventilation system
start-up, otherwise there is a risk of product malfunction.
To open the damper with the electric motor driven actuator, provi-
de power supply to the motor. Refer to the section Electrical con-
nections for further information.
To manually open the damper, use the handle supplied and carefully
rotate clockwise to the 90° indicator. To hold the damper in open
position operate on the lever indicated in figure.
During the manual opening of the damper, power must not be sup-
plied to the motor.
Position indication microswitches
The motorized versions are supplied with two microswitches to
show the blade's position (open or closed). Refer to the section
Electrical connections for further information.
Closing by remote control
If power to the motor is cut off, the blade will close.
Temperature calibration of thermosensitive element for auto-
matic damper closing
72 °C±7 °C (Standard)
95 °C±9 °C (On request).
Siemens motorized version
1. Position indicator
2. Screwdriver
3. Hex key for manual opening
4. Manual closing switch
Blade closing mode
Automatic closing with thermal fuse.
The control mechanism has a thermosensitive element that automa-
tically closes the blade when the temperature in the duct or in the
room exceeds 72°C (or 95°C for the 95°C version).
To close the damper when the motor is connected, press the switch
on the temperature sensor or cut off the power supply.
rev 20-12
3
We reserve the right to make changes without prior notice
