Lincoln Electric INVERTEC 275TP Operator'S Manual Download Page 26

English 24 English 

WEEE 

07/06 

 

Do not dispose of electrical equipment together with normal waste! 
In observance of European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE) 
and its implementation in accordance with national law, electrical equipment that has reached the end of its 
life must be collected separately and returned to an environmentally compatible recycling facility.  As the 
owner of the equipment, you should get information on approved collection systems from our local 
representative. 
By applying this European Directive you will protect the environment and human health! 

 

Spare Parts 

12/05 

Part List reading instructions 

  Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department 

for any code number not listed. 

  Use the illustration of assembly page and the table below to determine where the part is located for your particular 

code machine. 

  Use only the parts marked "X" in the column under the heading number called for in the assembly page (# indicate a 

change in this printing). 

 
First, read the Part List reading instructions above, then refer to the "Spare Part" manual supplied with the machine that 
contains a picture-descriptive part number cross-reference. 
 

REACh 

11/19 

Communication in accordance with Article 33.1 of Regulation (EC) No 1907/2006 – REACh. 

Some parts inside this product contain: 
Bisphénol A, BPA, 

 

EC 201-245-8, CAS 80-05-7 

Cadmium, 

 

 

EC 231-152-8, CAS 7440-43-9 

Lead, 

 

 

 

EC 231-100-4, CAS 7439-92-1 

Phenol, 4-nonyl-, branched, 

EC 284-325-5, CAS 84852-15-3 

in more than 0,1% w/w in homogeneous material. These substances are included in the “Candidate List of Substances of 
Very High Concern for Authorization” of REACh. 
Your particular product may contain one or more of the listed substances. 
Instructions for safe use: 

  use according to Manufacturer instructions, wash hands after use; 

  keep out of reach of children, do not put in mouth, 

 dispose 

in 

accordance 

with local regulations. 

 

Authorized Service Shops Location 

09/16 

  The purchaser must contact a Lincoln Authorized Service Facility (LASF) about any defect claimed under Lincoln's 

warranty period.  

  Contact your local Lincoln Sales Representative for assistance in locating a LASF or go to  

www.lincolnelectric.com/en-gb/Support/Locator

 

Electrical Schematic 

 
Refer to the "Spare Part" manual supplied with the machine. 
 

Summary of Contents for INVERTEC 275TP




























Reviews: