Lincoln Electric DUAL VANTAGE 700 Operator'S Manual Download

Page: 8 / 96

Page

Installation.......................................................................................................................Section A

Technical Specifications.......................................................................................................A-1

Safety Precautions ........................................................................................................A-2

VRD (Voltage Reduction Device)..................................................................................A-2

Location and Ventilation................................................................................................A-2

Storing...........................................................................................................................A-2

Stacking ........................................................................................................................A-3

Angle of Operation ........................................................................................................A-3

Lifting.............................................................................................................................A-3

High Altitude Operation .................................................................................................A-3

High Temperature Operation ........................................................................................A-3

Towing...........................................................................................................................A-3

Vehicle Mounting...........................................................................................................A-3

Pre-Operation Engine Service..............................................................................................A-4

Oil..................................................................................................................................A-4

Fuel and Fuel Cap.........................................................................................................A-4

Engine Coolant..............................................................................................................A-4

Battery Connection........................................................................................................A-4

Muffler Outlet Pipe ........................................................................................................A-5

Spark Arrestor ...............................................................................................................A-5

Air Cleaner Inlet Hood ..........................................................................................................A-5

Welding Terminals................................................................................................................A-5

Welding Output Cables .................................................................................................A-5

Machine Grounding.......................................................................................................A-5

Remote Control ....................................................................................................................A-6

Auxiliary Power Receptacles................................................................................................A-6

Standby Power Connections ........................................................................................A-6, A-7

Connection of Lincoln Electric Wire Feeders................................................................A-8, A-9

Connection of Wire Feeders with Control Cable (14 Pin).....................................................A-8

Connection of Across the Arc Wire Feeders ........................................................................A-9

Electrical Device use with this Product...............................................................................A-10

________________________________________________________________________________

Operation.........................................................................................................................Section B

Safety Precautions ..............................................................................................................B-1

General Description..............................................................................................................B-1

Auxiliary Power ............................................................................................................B-1

Engine Operation ..........................................................................................................B-1

Add Fuel ...............................................................................................................................B-2

Hand Primer Button..............................................................................................................B-2

Recommended Applications.................................................................................................B-2

Generator .............................................................................................................................B-2

Welding Controls ....................................................................................................B-3 thru B-4

Engine Controls....................................................................................................................B-5

Engine Operation .................................................................................................................B-6

Welder Operation ...................................................................................................B-7 thru B-9

Constant Current (CC-Stick) Welding ...........................................................................B-7

Downhill Pipe Welding ..................................................................................................B-7

TIG Welding ..................................................................................................................B-8

Typical Current Ranges for Tungsten Electrodes .........................................................B-8

Wire Welding-CV...........................................................................................................B-9

Arc Gouging ..................................................................................................................B-9

Paralleling .....................................................................................................................B-9

Auxiliary Power Operation..................................................................................................B-10

Simultaneous Welding and Auxiliary Power Loads.....................................................B-10

Extension Cord Length Recommendations.................................................................B-10

Accessories ........................................................................................................Section C

Optional Field Installed Accessories .....................................................................C-1

________________________________________________________________________

TABLE OF CONTENTS

DUAL VANTAGE

700

Summary of Contents for DUAL VANTAGE 700

































































































Search results

Summary of Contents for DUAL VANTAGE 700

Reviews:

Related manuals for DUAL VANTAGE 700

Brands by name

Popular brands

Lincoln Electric DUAL VANTAGE 700, Operator'S Manual

Search results

Summary of Contents for DUAL VANTAGE 700

Reviews:

Related manuals for DUAL VANTAGE 700

Brands by name

Popular brands