Lightware MX-FR17, User Manual

Page: 180 / 190

11. Appendix MX-FR Series Modular Matrix Frames – User's Manual 180
Applied CPU2 firmware: v3.5.7b8 | LDC software: v2.5.17b2
▪ Some error log events were disappeared if the last error was too close in time.
▪
:HDCPRESET command may have freezeed the communication
▪ HDCP LED sometimes had false blinking on MX-HDMI-IB
▪ There was erroneous HDCP handling if more than 20 keys were received from an HDCP capable sink.
This may have resulted reboot.
3.1.8
Released: 2011-09-30
New feature
▪ MX-DVI-OPT-OB v24 support.
Bugfix
▪ The response for {VM} command (View Mute state) now starts with "MUT" (not "ALL") according to the
product manual.
▪ Matrix may have restarted because of internal communication problems in case of DVI-HDCP and
HDMI I/O boards.
3.1.9
Released: 2011-10-10
Bugfix
▪ The response to the WB# command was different from the one described in the user manual. A number
was missing at the end of the line.
3.2.0
Released: 2011-11-02
Bugfix
▪ In Protocol#2 the matrix did a switch to all for a single switch command. Now it's fixed.
3.2.2
Released: 2011-11-23
Bugfix
▪ Connecting an HDCP capable optical RX/TX to an MX-HDMI-OPT-IB/OB, noisy signal on the
communication channel could cause fatal buffer overflow error and restarting of the router. In special
cases the router could run an infinite restart loop.
3.2.3
Released: 2011-12-12
New feature
▪ Supports MX-3GSDI-IB.
3.2.5
Released: 2012-02-20
Bugfix
▪ New standard timing descriptors are applied. Standard resolution list now contains 1024x768@60 and
1920x1080@60 resolutions.
▪ Factory EDIDs had a bug - the digital sync was not set properly in the detailed timing descriptor blocks.
Sometimes this caused error with analog sources.
▪ MX-DVI-OPT-OB 2.0 outputs flashed when a laser enable command was sent to any port.
▪ Preview output didn't convert down the deepcolor modes to HDMI 24bit in auto mode if the display
didn't support deepcolor.
▪ An extra 0-byte length short descriptor was present in the CEA data block. This may have led to
incompatibility with some sources.
▪ Analog 1920x1200p60 was not recognized due to enabled hsync dejitter filter and high sync detection
threshold on the DVI-I board.
▪ ASUS EAH3650 video card can send a strange analog format in 1280x720p60 and 1920x1080p60.
These resolutions are added to the factory preset list now.
▪
The 4-line LCD mismatched the 0dB and Auto EQ options in the MX-DVID-IB settings menu.
▪ On the 4 line LCD at the "Switch EDID" menu item it is possible to select factory and user EDIDs, not just
dynamic EDIDs.
▪ Too many cached HDCP keys could lead to reboot.
▪
If an EDID switch happens while the source is reading the data, then the input board could fail (MX-
HDMI-IB, MX-DVI-HDCP-IB, MX-HDMI-TP-IB)
3.2.6
Released: 2012-03-01
New feature
▪ In case of FR33R the insertion and removal of the PSUs are logged.
Bugfix
▪ The matrix could fail to boot in case of wrong RTC.
▪ Invalid EDIDs cannot be switched to input ports anymore.
▪ The reply for {FC} command now contains the version of the FR33R PWR_SUM board.
▪ HDCP handling of preview output in MX-FR80 didn't work properly.
▪ MX-HDMI-OPT-IB didn't detect if the link was terminated. (The bug appeared in 3.1.6)
3.2.7
Released: 2012-05-30
New feature
▪ Support for MX-FR33L
▪
Pixel phase can be adjusted and saved with SMPTE compliant analog component/rgbhv incoming
signals.
   