Lightspeed TOPCAT Registration Manual Download Page 12

REMOTE REGISTRATION FOR SHAREMIKE

ADDING OR REPLACING A SHAREMIKE USING THE REMOTE

4.  Slide open the Sharemike battery compartment. The 

1.  Start with the Topcat plugged in and powered on. To verify it is 

powered on, there will be a blue power light on the front of the 

Topcat.

2.  If replacing a Sharemike, make sure the malfunctioning Sharemike is 

powered off.

3.  Power on the new Sharemike. Both microphone 1 and 2 blue 

lights should be blinking.

registration button is located below the battery on the left side, marked 

REG.

5.  Determine what number microphone you wish to register, 1 or 2:

• 

Sharemike is typically registered as mic 2

.

6.  On the remote, in rapid succession, press: 

7.  The center button on the remote will begin blinking and the 1 and 2 lights on the Topcat will be blinking alternately.
8.  Using a paperclip with the end straightened out, briefly press the registration button on the Sharemike. The 1 and 2 lights will be blinking alternately.

9.  After several seconds, the #2 lights on the Topcat and the Sharemike will turn solid. 
10.  The registration is complete. Press the center button on the remote and begin speaking into the Sharemike to verify there is 

audio.

11.  Place system ID number (attached to the Topcat Quickstart guide) on the new Sharemike.

NOTE: 

if at any point, the Topcat or Sharemike lights begin blinking rapidly, that indicates a registration error. Turn off the 

Sharemike, then repeat steps 3-8.

Vol

Vol

Mute

6

5

1

3

2

4

UP

DN

A

B

C

Volume 

Down

Mute

#1 or #2

A

B

C

Blinking lights

 

Registration 

Button

Power On

Blinking lights

Sharemike

SYS

TEM ID#

SYS

TEM ID#

SYS

TEM ID#

SYS

TEM ID#

SYS

TEM ID#

RETAIN EXTRA LABELS IN THE EVENT A COMPONENT IS REPLACED OR ADDED. 

Ma

tch components

to this system ID#

Apply to system components to indicate which parts are registered 

as a system.  Keep registered items together when storing away.

Registration ID Labels

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

00-01

334-0162-02-00-01

10101

TOPCAT ACCESS REGISTRATION GUIDE

Vol

Vol

Mute

6

5

1

3

2

4

UP

DN

Topcat 

Access

Blinking lights

Topcat 

Access

Solid light

Summary of Contents for TOPCAT














Reviews: