background image

 

 
 
 
 
 
 
 
 
 
 

All Lightronics products are warranted for a period of TWO/FIVE YEARS from the date of 
purchase against defects in materials and workmanship. 

 

 
 
 

This warranty is subject to the following restrictions and conditions: 

 
A)  If service is required, you may be asked to provide proof of purchase from an authorized 
 Lightronics 

dealer. 

 
B)  The FIVE YEAR WARRANTY is only valid if the warranty card is returned to Lightronics 
 

accompanied with a copy of the original receipt of purchase within 30 DAYS of the 

 

purchase date, if not then the TWO YEAR WARRANTY applies.   Warranty is valid only for 

 

the original purchaser of the unit. 

 
C)  This warranty does not apply to damage resulting from abuse, misuse, accidents, shipping, 
 

and repairs or modifications by anyone other than an authorized Lightronics service 

 representative. 
 
D)  This warranty is void if the serial number is removed, altered or defaced. 
 
E)  This warranty does not cover loss or damage, direct or indirect arising from the use or 
 

inability to use this product. 

 
F)  Lightronics reserves the right to make any changes, modifications, or updates as deemed 
 

appropriate by Lightronics to products returned for service.  Such changes may be made 

 

without prior notification to the user and without incurring any responsibility or liability for 

 

modifications or changes to equipment previously supplied.  Lightronics is not responsible 

 

for supplying new equipment in accordance with any earlier specifications. 

 
G)  This warranty is the only warranty either expressed, implied, or statutory, upon which the 
 

equipment is purchased.  No representatives, dealers or any of their agents are authorized 

 

to make any warranties, guarantees, or representations other than expressly stated herein. 

 
H)  This warranty does not cover the cost of shipping products to or from Lightronics for 
 service. 
 
I) 

Lightronics Inc. reserves the right to make changes as deemed necessary to this warranty 

 

without prior notification. 

 

Lightronics 

Inc. 

     509 

Central 

Drive 

 

Virginia 

Beach, 

 

VA 

23454 

     20050125

WARRANTY

 

 

Summary of Contents for RD-121















Reviews: