background image

-  1

-

Strike S2.300

Strike S2.500

• 

Power  RAting

: 90w x 2 @ 4 ohms

170w x 2 @ 2ohms (less than 1% THD)

340w x 1 @ 4ohms

• 

Input  SensitiVity

: 150mV minimum

• 

High  LeVel  Input

: 1V - 8V

• 

SignAl  to  Noise  rAtio

: Greater than 90dB

• 

ChAnnel  SepArAtion

: Greater than 55dB

• 

CrossoVer

: 60-400Hz Variable, High/Low/ All Pass switch

• 

CrossoVer  Slope

: 12 dB/Octave

• 

EquAlizAtion

: Remote Juice Boost, 

Va12dB @ 50Hz (Remote included)

• 

amplifier  Fuse  VAlue

:  (2) 20A

• 

chAssis  size

:  10.25”W x 2.25”H x 10.0”L*

• 

Power  RAting

: 150w x 2 @ 4ohms

250w x 2 @ 2ohms (less than 1% THD)

500w x 1 @ 4ohms

• 

Input  SensitiVity

: 150mV minimum

• 

High  LeVel  Input

: 1V - 8V

• 

SignAl  to  Noise  rAtio

: Greater than 90dB

• 

ChAnnel  SepArAtion

: Greater than 55dB

• 

CrossoVer

: 60-400Hz Variable, High/Low/All Pass switch

• 

CrossoVer  Slope

: 12 dB/Octave

• 

EquAlizAtion

: Remote Juice Boost

Va12dB @ 50Hz (Remote included)

• 

amplifier  Fuse  VAlue

:  (3) 20A

• 

chAssis  size

:  10.25”W x 2.25”H x 17.0”L*

SpecificAtions

• 

Power  RAting

:60w x 2 @ 4ohms

100w x 2 @ 2ohms (less than 1% THD)

200w x 1 @ 4ohms

• 

Input  SensitiVity

:150mV minimum

• 

High  LeVel  Input

: 1V - 8V

• 

SignAl  to  Noise  rAtio

: Greater than 90dB

• 

ChAnnel  SepArAtion

: Greater than 55dB

• 

CrossoVer

: 80Hz High/Low/All Pass switch

• 

CrossoVer  Slope

: 12dB/Octave

• 

EquAlizAtion

: –

• 

amplifier  Fuse  VAlue

:  (1) 25A

• 

chAssis  size

:  10.25”W x 2.25”H x 8.5”L*

Specifications subject to change without notice

StriKe S2.200

Strike S2.250

• 

Power  RAting

: 75w x 2 @ 4ohms

115w x 2 @ 2ohms (less than 1% THD)

230w x 1 @ 4ohms

• 

Input  SensitiVity

: 150mV minimum

• 

High  LeVel  Input

: 1V - 8V

• 

SignAl  to  Noise  rAtio

: Greater than 90dB

• 

ChAnnel  SepArAtion

: Greater than 55dB

• 

CrossoVer

: 60-400Hz Variable, High/Low/All Pass switch

• 

CrossoVer  Slope

: 12dB/Octave

• 

EquAlizAtion:

Juice Boost +6dB @ 50Hz (on/off switch)

• 

amplifier  Fuse  VAlue

:  (1) 30A

• 

chAssis  size

:  10.25”W x 2.25”H x 8.5”L*

2-ChAnnel  Amplifiers

*End Cap adds 2.4” to Chassis length

Summary of Contents for S2.200





























Reviews: