background image

LIGHT PROGRESS 

 

 

 

 

 

 

 

 

 

    DIRECT-H-K [eng]

 

 

 

gen-2021 

 

Pag. 3/16

 

 

CONVENTIONAL SYMBOLS NOTICED ON DEVICES

 

 

 

DOESN’T DISPOSE THIS PRODUCT ON THE UNDIFFERENTIATED WASTE DISPOSING OF THE 

 

 

SUBSTITUTED ITEMS MUST BE PERFORMED RESPECTING THE LOCAL LAWS. 

 
 
 

 

RECYCLE THE STUFFS THAT COMPOSES THIS PRODUCT. 

 
 
 
 

 

OBLIGATION TO CONSULT THESE INSTRUCTIONS BEFORE USE THIS PRODUCT 

 
 
 

DANGER OF ELECTRICAL SHOCK; REMOVE TENSION TO THE SYSTEM BEFORE PERFORMING 
ANY OPERATION. 

 
 
 
 

 

GENERIC DANGER. 

 
 
 
 

 

DANGER OF EXPOSITION TO ULTRAVIOLET UV-C RAYS. 

 
 
 
 

 

THIS DEVICE RESPECTS THE ROHS NORMS. 

 
 
 
 

 

USE PROTECTIVE GLOVES 

 
 
 
 

 

WEAR PROTECTIVE GLASSES 

 
 
 

STORAGE OF THIS MANUAL

 

 

 

 

ATTENTION!

 

 

 

This instruction manual must be preserved and be ever at disposal to consultation; it must follow the device in 
case of passage of property, and accompany the device until its demolition

 

To request the  instruction  manual updated  and to  ask all other information  needed, it’s possible to contact the Light 
Progress

’ technical office. 

 

DEMOLITION AND DISPOSAL 

 

Do  not  dispose  of  these  products  as  unsorted  municipal  waste,  but  collect  them  separately  as  a  special 
waste  and  entrust  them  to  specialized  waste  disposal  companies.  Disposal  should  be  in  accordance  with 
Legislative Decree No. 151/2005 (WEEE - Italy), or the law of the country where disposal will occur (WEEE - 
EC). In case of failure to comply with laws or  illegal disposal heavy penalties are provided. The  apparatus 
consists  of plastic  parts,  electronic  components,  metal,  UV  lamps  containing  mercury  (substances  danger-

ous for the environment and human health). The dealer is available to the withdrawal of the apparatus used.

 

Summary of Contents for UV-DIRECT

















Reviews: