LIGHT MY BRICKS LEGO Winter Village Post Office 10222 Instructions Manual Download Page 27 | Manualshive

Page: 27 / 70

background image

Take a

5cm Connecting Cable

and connect it to the other port on the Strip

Light, then using it’s adhesive backing, stick the strip light underneath the roof
in the following position: Ensure the 5cm cable is facing the back along with
the rest of the cables.

13.)

Flip the roof back over, then reconnect it to the gazebo. Connect all 5 cables

«
...
25
26
27
28
29
...
»

Summary of Contents for LEGO Winter Village Post Office 10222







































































Reviews:

No comments

Related manuals for LEGO Winter Village Post Office 10222

Brand: zipwake Pages: 2

Brand: zipwake Pages: 2

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

Brand: Cadman Pages: 66

WJHD309 - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 7

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 24

Brand: Facsimile Pages: 16

Brand: ParaBody Pages: 5

Brand: iHealth Pages: 8

Brand: jablotron Pages: 2

Brand: jablotron Pages: 2

Brand: Öhlins Pages: 8

Brand: &Tradition Pages: 3

Flowerpot VP3 Verner Panton 1968

Brand: &Tradition Pages: 3

Brand: ?HC Pages: 2

FLOWERPOT GARDEN VP5

Brand: &Tradition Pages: 4

FLOWERPOT GARDEN VP3

Brand: &Tradition Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands