LIGHT MY BRICKS LEGO Winter Village Post Office 10222 Instructions Manual Download Page 1

Page: 1 / 70

The following page is the instructions for the

Light My Bricks LEGO Winter

Village Post Office (10222) LED light kit.

If you run into any issues, please refer to the

online troubleshooting guide.

To ensure a trouble-free installation of your light kit, please read and follow

each step carefully. These instructions can be downloaded in PDF format

here

Please note: This page lists instructions for the LED light kit only. If you are

wishing to purchase the Light My Bricks LEGO Winter Village Post Office (10222)

LED light kit , please click

here

to view the product page

Light My Bricks: LEGO Winter Village Post

Ofﬁce 10222 Lighting Kit

Summary of Contents for LEGO Winter Village Post Office 10222







































































Search results

Summary of Contents for LEGO Winter Village Post Office 10222

Reviews:

Related manuals for LEGO Winter Village Post Office 10222

Brands by name

Popular brands

LIGHT MY BRICKS LEGO Winter Village Post Office 10222, Instructions Manual

Search results

Summary of Contents for LEGO Winter Village Post Office 10222

Reviews:

Related manuals for LEGO Winter Village Post Office 10222

Brands by name

Popular brands