background image

10.  MODELS T3i AND T5i ONLY

 Locate the HANDRAIL CROSSBAR

(#9). With the bend facing upward and pitched toward the DISPLAY
CONSOLE, carefully place the HANDRAIL CROSSBAR between the
user left and right handrails as shown and align the mounting holes.
Insert one SHORT MOUNTING BOLT (#6) on either end of the
HANDRAIL CROSSBAR and tighten using a 5/32” hex key wrench.

Securely tighten all mounting bolts on the USER LEFT HANDRAIL.

11. 

Securely tighten the four MOUNTING BOLTS (#10) securing the
USER LEFT and RIGHT UPRIGHTS to the FRAME (B).

12. 

Position the MOTOR COVER (A) back over the MOTOR
COMPARTMENT (E) and secure the MOTOR COVER to the
FRAME (B) using the two MOTOR COVER SCREWS (#13). Tighten
the screws securely.

NOTE: BE CAREFUL NOT TO PINCH THE WIRE HARNESS (C)
WHEN REPLACING THE MOTOR COVER (A).

13. 

Place the stop cord (#12) in the proper location.

PRE-OPERATION CHECKLIST

4

 

Ensure that all fasteners are tight.

4

 

Make sure the STRIDING BELT is properly tensioned and aligned according to the Operation
Manual.

4

 

Check the operation of the STOP switch and tether switch assembly.

(See Operation Manual.)

4

 

Confirm the display console is set to English or Metric units.

(See Optional Settings ENG/MET in Operation Manual.)

4

 

Read the entire Operation Manual before using the treadmill.

Before attempting to operate your Treadmill, it is imperative that you familiarize yourself with the contents of the Operation
Manual. If your Life Fitness treadmill does not respond as described in the OPERATION MANUAL contact the nearest Life
Fitness Service Center as listed in the OPERATION MANUAL.

Life Fitness Customer Support Services

at (800) 351-3737 or (847) 451-0036

Prior to your call, please be sure you have located and noted the

MODEL NUMBER & SERIAL NUMBER.

The Model & Serial number information of your Life Fitness Treadmill is contained in a label

located on the front of the unit.

6

9

12

2000 Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, and FlexDeck are trademarks of Brunswick Corporation.

6841801

4/00

A

H

B

Summary of Contents for T3









Reviews: