IMPORTANT!
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY
COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
1.
Remove the tape securing the MOTOR COVER (A) to the FRAME
(B). Carefully lift and remove the MOTOR COVER.
2.
Remove the USER LEFT UPRIGHT (#1) (with grommets installed)
from the ship kit. With the USER LEFT UPRIGHT angled toward the
rear of the unit, align the mounting holes of the flanged end of the
USER LEFT UPRIGHT with those on the top of the FRAME (B).
Using two BOLTS (#10), secure the USER LEFT UPRIGHT to the
FRAME. Tighten the BOLTS using a 9/16” combination wrench until
snug and then back them off 1/4 turn. Repeat the procedure for the
USER RIGHT UPRIGHT (#2).
3.
Locate the DISPLAY CONSOLE ASSEMBLY (#3). Unwrap the
WIRE HARNESS (C) secured to the back of the DISPLAY
CONSOLE ASSEMBLY. Standing at the front of the unit, carefully
lower the DISPLAY CONSOLE ASSEMBLY down near the tops of
the USER LEFT and RIGHT UPRIGHTS (#1 & #2). Lower the user
right side of the DISPLAY CONSOLE ASSEMBLY to rest on the
USER RIGHT UPRIGHT. Holding the user left side of the DISPLAY
CONSOLE ASSEMBLY slightly above the USER LEFT UPRIGHT,
feed the WIRE HARNESS down into the USER LEFT UPRIGHT
through the TOP CABLE ROUTING HOLE (D) of the USER LEFT
UPRIGHT. Once the WIRE HARNESS is completely inserted into
the USER LEFT UPRIGHT, lower the DISPLAY CONSOLE
ASSEMBLY to completely rest on the USER LEFT UPRIGHT.
NOTE: BE CAREFUL NOT TO DAMAGE THE
WIRE HARNESS (C) WHEN ROUTING IT THROUGH THE
USER LEFT UPRIGHT (#1).
NOTE: BE CAREFUL NOT TO PINCH THE WIRE HARNESS
(C)
WHEN LOWERING THE DISPLAY CONSOLE ASSEMBLY (#3)
ONTO THE USER LEFT UPRIGHT (#1).
4. MODELS T3 AND T5 ONLY (Models T3i and T5i Skip to Step 5)
Locate the HANDRAIL (#11) and one TOP HANDRAIL SPACER
(#5). On the user right side of the HANDRAIL insert a SHORT
MOUNTING BOLT (#6) through the bottom most of the three top
mounting holes of the HANDRAIL. Slide the TOP HANDRAIL
SPACER over the SHORT MOUNTING BOLT as shown until it fully
nests over the. Slide the HANDRAIL with the TOP HANDRAIL
SPACER over the user right end of the display console and upright.
Align and insert the SHORT MOUNTING BOLT into the bottom most
mounting holes of the user right UPRIGHT. Tighten the bolt until
snug and. Insert two LONG MOUNTING BOLTS (#7) through the
two remaining mounting holes and tighten all three bolts securely
using a 5/32” hex key wrench. Leave the user left side of the
HANDRAIL unfastened at this time. Continue to
Step 7
.
5.
MODELS T3i AND T5i ONLY
Locate a HANDRAIL (#4) and a TOP
HANDRAIL SPACER (#5). Insert a SHORT MOUNTING BOLT (#6)
through the bottom most of the three top mounting holes of the
HANDRAIL. Slide the TOP HANDRAIL SPACER over the SHORT
MOUNTING BOLT as shown until it fully nests over the HANDRAIL
Align and insert the SHORT MOUNTING BOLT into the bottom most
mounting hole of the USER LEFT UPRIGHT (#1). Tighten the bolt until
snug and then back it off one full turn. Insert two LONG MOUNTING
BOLTS (#7) through the two remaining mounting holes and tighten all
three bolts securely using a 5/32” hex key wrench.
A
B
1
B
10
3
C
1
D
5
1
4
7
6
5
7
11
