background image

DL-HD2A-RX Owners Manual

3

Important Safety Instructions

 

»

Please completely read and verify you understand all instructions in this manual before operating this equipment. 

 

»

Keep these instructions in a safe, accessible place for future reference. 

 

»

Heed all warnings. 

 

»

Follow all instructions. 

 

»

Do not use this apparatus near water. 

 

»

Clean only with a dry cloth. 

 

»

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) 

that produce heat. 

 

»

Use only accessories specified or recommended by Intelix.

 

»

Explanation of graphical symbols: 

◊  Lightning bolt/flash symbol: the lightning bolt/flash and arrowhead within an equilateral triangle 

symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the 

product enclosure which may be of sufficient magnitude to constitute a risk of shock to a person or 

persons. 

◊  Exclamation point symbol: the exclamation point within an equilateral triangle symbol is intended 

to alert the user to the presence of important operating and maintenance (servicing) instructions 

in the literature accompanying the product. 

 

»

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR 

MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.

 

 

»

Use the mains plug to disconnect the apparatus from the mains. 

 

»

THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE. 

 

»

Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider 

than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong 

is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of 

your obsolete outlet. 

Caution! To reduce the risk of electrical shock, grounding of the center pin of this plug must be 

maintained. 

 

»

Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and the 

point where they exit from the apparatus. 

 

»

Do not block the air ventilation openings. Only mount the equipment per Intelix’s instructions. 

 

»

Use only with the cart, stand, table, or rack specified by Intelix or sold with the equipment. When/if a 

cart is used, use caution when moving the cart/equipment combination to avoid injury from tip-over. 

 

»

Unplug this apparatus during lightning storms or when unused for long periods of time. 

 

»

Caution!

 Shock Hazard. Do not open the unit. 

 

»

Refer to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as 

power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus 

has been exposed to rain or moisture, does not operate normally, or has been dropped.  

Summary of Contents for DigitaLinx DL-HD2A-RX





















Reviews: