background image

LGMG North America Inc.

                                                                   

Maintenance Manual

 

15 

1.19 Engine fault table

 

Faults 

Cause 

Measures 

Engine  does  not  start  or  is  difficult  to 
start 

Not disconnected (if possible) 

Check coupling 

Fuel tank empty 

Tanks 

Fuel suction pipe blocked 

Check 

Below starting limit temperature 

Check 

Cold starting device 

Check/replace 

Wrong  SAE  viscosity  class  of  the 
engine lubricating oil 

Change the lubricating oil 

Fuel  quality  does  not  comply  with 
operating manual 

Change the fuel 

Battery defective or discharged 

Check battery 

Cable  connection  to  starter  loose  or 
oxidized 

Check cable connections 

Starter  defective  or  pinion  does  not 
engage 

Check starter 

Air  filter  clogged  /  turbocharger 
defective 

Check/replace 

Air in fuel system 

Vent fuel system 

Compression pressure too low 

Check compression pressure 

Exhaust gas backpressure too high 

Check 

Injection line leaks 

Check injection line 

High-pressure pump defective 

Check/replace 

Engine  does  not  start  and  diagnostic 
lamp flashes 

Engine electronics prevents starting 

Check  error  according  to  error  code 
and eliminate error if necessary 

Engine  starts,  but  runs  irregularly  or 
fails 

Exhaust gas backpressure too high 

Check 

Compression pressure too low 

Check compression pressure 

Cold starting device 

Check/replace 

Air in fuel system 

Vent 

Fuel filter contaminated 

Clean 

Fuel  quality  does  not  comply  with 
operating manual 

Change the fuel 

Injector defective 

Change 

Injection line leaks

 

Check injection line 

Engine cable harness defective 

Check/replace

 

Speed  changes  are  possible  and 
diagnostic lamp lights up 

Engine  electronics  has  detected  a 
system 

error 

and 

activates 

an 

equivalent speed 

Check  error  according  to  error  code 
and eliminate error if necessary 

Engine becomes excessively hot. 
Temperature warning system activates 

Vent line blocked 

Clean 

Lube oil cooler defective 

Check/replace 

Lube  oil  filter  contaminated  on  the  air 
or lube oil side 

Change 

Lube oil level too high 

Check lube oil level, if necessary drain 
off. 

Lubricating oil level too low

 

Fill up lube oil 

Injector defective 

Change 

Summary of Contents for T65J







































Reviews: