LG WF-S5707PP Service Manual Download

Page: 33 / 56

4-6. TEST RUNNING WITHOUT W ATER

1) METHOD TO USE QC TEST MODE

EXTRA

ALTO

MEDIO

BAJO

FUZZY

RAPIDO

JEAN

LANA

REMJO RAPIDO

LAVADO

ENJUAGUE

CENTRIFUGADO

• To use the CHECK PROGRAM (QC TEST MODE), press PROCESS key, and PROGRAM key at the

same time and then the POWER switch on without depositing any laundry.

CHECK METHOD

LED INDICATOR

CHECK ITEM

Initial state

Press once

Press twice

Press 3 times

Press 4 times

Press 5 times

Press 6 times

Press 7 times

• After laundry amount detecting,

LED indicates laundry amount
and NIVEL DE AGUA.

• Pump model: MEDIO water

level Led ON.

• Non-pump model:water level

MEDIO water level Led OFF.

• All LED on.

• After 2~3 seconds water level

frequency is displayed on LED.

• Laundry amount test.

• After checking laundry amount, motor

is on. (Left & Right)

• Cold water

• Hot water.

• Drain motor is 1st state is play.
• If lid is opened door error display.

(wash and spin LED blinks)

• Drain motor is 2nd state.(Only WF-T Series)

• Drain pump is on.

• AUTO off switch.

• WATER LEVEL FREQUENCY & LAUNDRY AMOUNT ARE DISPLAY BY THE LED (WATER LEVEL,

PROCESS, PROGRAM)

Ex) Water level check ; Frequency : 26.7 KHz

Ex) Laundry amount ; Water level : MEDIO

Pulse : 25

EXTRA

ALTO

MEDIO

BAJO

FUZZY

RAPIDO

JEAN

LANA

REMJO RAPIDO

LAVADO

ENJUAGUE

CENTRIFUGADO

Summary of Contents for WF-S5707PP

























































Search results

Summary of Contents for WF-S5707PP

Reviews:

Related manuals for WF-S5707PP

Brands by name

Popular brands

LG WF-S5707PP, Service Manual

Search results

Summary of Contents for WF-S5707PP

Reviews:

Related manuals for WF-S5707PP

Brands by name

Popular brands