LG WF-S5707PP Service Manual Download Page 40

Page: 40 / 56

6) Pulsator doesn

’t r otate normally

Where, what & how to check?

Result of Check

Possible Cause How to repair & settle

Pulsator rotates at one
direction.

1. The Pulsator rotates normally at the

beginning of wash cycle, but is it not
rotate at clockwise direction (locked)

after some wash cycles though there
is motor-working sound?

2. In the case the pulsator doesn’t

rotates either clockwise or
counterclockwise from the beginning
of wash cycle:

1) Check resistance of the wash

motor if there is no motor-working
sound.

2) Check belt tension & whether the

clutch rotates normally if there is
motor-working sound.

3. The pulsator doesn’t rotate at both

directions.

1) Check whether motor rotates at

both directions if there is motor-
working sound when it’s
energized.

2) Check resistance of the motor if

there is no motor-working sound.

Clockwise
rotation locked.

Resistance
is normal.

V-belt is loose.

Clutch locked.

Motor rotates
at both
directions.

Motor doesn’t
rotates at both
directions.

Normal
resistance.

Unusual operation.

Defect of
controller or poor
contact of
connectors of
motor leads.

Loose the belt.

Defect of the
clutch.

Loose the belt.

The plusator
locked.

Defect of the
clutch.

Defect of the
capacitor.(check
the capacitor’s
capacitance)

Defect of the
motor.

Motor coil is open.

Contact defect of
the leads.

Turn the power off
and on again then that
symptom disappears.
Explain “Don’t run wash

only continuously”.

Change the controller if
there are no contact
defects in the leads of

the motor.

Adjust belt tension by
changing motor fixing
location and change the
belt if it is impossible to
adjust belt tension.

Change the clutch if the
clutch pulley is locked
when making it rotated
clockwise and
counterclockwise by
hand.

Adjust belt tension or
change the belt if it is
impossible to adjust.

Remove cause
locking the pulsator

Change the clutch.

Change the motor if the
motor is locked when
having its shaft rotated
by hand.

Change the capacitor if
there is no contact defect
in capacitor’s lead

Change the motor.

Remove the causes.

Summary of Contents for WF-S5707PP

























































Search results

Summary of Contents for WF-S5707PP

Reviews:

Related manuals for WF-S5707PP

Brands by name

Popular brands

LG WF-S5707PP, Service Manual

Search results

Summary of Contents for WF-S5707PP

Reviews:

Related manuals for WF-S5707PP

Brands by name

Popular brands