LG VR6140LVM Owner'S Manual Download Page 26

Page: 26 / 40

SMART-DIAGNOSIS MODE

Please refer to the table below to measure if voice message is heard after the smart diagnosis.

Voice message

Measures (Reference Page)

Starting smart diagnosis mode. Please step away and

remove any items within 1 meter.

Please step away and clear out stuff around home

station within 1

until smart diagnosis is complete. (23p)

Unable to initiate smart diagnosis due to a low battery.

Please restart the smart diagnosis function after battery

is charged. (16p)

Smart Diagnosis mode will not operate with the mop plate

attached. Please try again after removing it.

Please start smart diagnosis again after removing the

mop plate.

HomBot will not charge due to infrared sensor error. Please try

smart diagnosis again after turning the main power switch on

the bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

HomBot will not charge due to ultrasonic sensor error. Please try

smart diagnosis again after turning the main power switch on

the bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

HomBot will not charge due to a problem with the cliff

sensors on bottom. Please wipe the sensors clean.

Please clean 3 cliff detection sensors on the bottom of

HOM-BOT 2.0. (28p)

Please clean the camera sensor on bottom right side.

Please wipe the lower camera sensor on the right

bottom of the unit.(28p)

A problem has been found on the Gyro Sensor. Please try smart

diagnosis again after turning the main power switch on the

bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

Please check for foreign material on the left wheel.

Please check dirt on the left wheel. (31p)

Please check for foreign material on the right wheel.

Please check dirt on the right wheel. (31p)

A problem has been found on the left wheel sensor. Please try

smart diagnosis again after turning the main power switch on

the bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

A problem has been found on the right wheel sensor. Please try

smart diagnosis again after turning the main power switch on

the bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

A problem has been found with the brush. Please check for

any foreign material.

Please check if foreign material is on the rotation brush.

(33p)

A problem has been found in the suction motor. Please try

smart diagnosis again after turning the main power switch on

the bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

A problem has been found in the acceleration sensor. Please try

smart diagnosis again after turning the main power switch on

the bottom of the HomBot 'Off' then 'On' again. If the problem

continues, please contact LG Electronics customer care.

If same message pops up even after the second smart

diagnosis, please contact LG Electronics service center.

Please, check the dust bin.

Please open the cover to check dust bin.(32p)

Smart diagnosis has failed to complete its diagnostics.

Please try again after turning the main power switch on the

bottom of the HomBot 'Off' then 'On' again.

Please try smart diagnosis again after turning on and

off the main power switch on the bottom of HOM-BOT

2.0 and do not touch or disturb HOM-BOT 2.0 until

the smart diagnosis is complete.

Summary of Contents for VR6140LVM









































Search results

Summary of Contents for VR6140LVM

Reviews:

Related manuals for VR6140LVM

Brands by name

Popular brands

LG VR6140LVM, Owner'S Manual

Search results

Summary of Contents for VR6140LVM

Reviews:

Related manuals for VR6140LVM

Brands by name

Popular brands