background image

-3-

SAFETY PRECAUTIONS

BEFORE OPERATING THIS VACUUM CLEANER, READ THIS SERVICE MANUAL THOROUGHLY,
AND OBSERVE EACH POINT CAREFULLY.

1. Change the paper bag or clean the cloth

bag in case the indicator moves toward red.

1) If the dust bag is full, intake power will be reduced.
2) When the dust bag is full of dust, pull out the dust

bag from the inside of body base.

2. Filter

1) The filter is composed of a clean filter, an exhaust fil-

ter and a paper bag or a cloth bag.

2) Never use the vacuum cleaner without filters. 

It may harm to the motor.

3) When the cloth bag, the clean filter and the exhaust

filter are soiled, wash the filter with neutral cleanser.

Note : Re-use of the cloth bag, clean filter and exhaust

filter.

• Never wash the filter in a washing machine or in a

dishwasher.

• Never use hot water for washing the filter.
• Re-use the filter after drying it completely in the shade.
• Do not dry near fire or direct sun ray.

3. Dust indicator

Dust indicator shows you red color when the filter is full
of dust.
Then, change the paper bag with new one or clean the
cloth bag.

4. Avoid suction such materials as:

1) Liquid or wet dust:

Clogging the ventilation holes, reduces the intake
power significantly and harms the motor.

2) Inflammable liquids such as benzene, alcohol or sol-

vents.

3) Burning objects such as cigarette butts.
4) Bulky objects such as vinyl, paper etc.
5) Sharp objects such as needles, pins, metal or glass

particles etc.

5. Attachments

• Nozzle : For cleaning wooden floor, the room floor and

carpet.

• Crevice Tool: for cleaning any crevice, inside corners

of window frames.

However, do not use the crevice tool more than 20 min-
utes because it may cause harm to the motor.

6. Close supervision is necessary when this

vacuum cleaner is used by or near children.
Children's carelessness may cause damage
to the cleaner or injure persons.

7. Air exhausted from the vacuum cleaner is

normally warm. But if extraordinarily hot air
is exhausted, check if the telescopic tube,
hose or dust bag is clogged or not.

8. Electric shock could occur if used outdoors

or on wet surfaces.

Summary of Contents for V-CB564ST





















Reviews: