LG UU09W ULD Installation Manual Download Page 8

Page: 8 / 49

Installation of Indoor, Outdoor Unit

Convertible type

• Do not have any heat or steam near the unit.
• Select a place where there are no obstacles in

front of the unit.

• Make sure that condensation drainage can be

conveniently routed away.

• Do not install near a doorway.
• Ensure that the interval between a wall and

the left (or right) of the unit is more than
20cm.

• Use a stud finder to locate studs to prevent

unnecessary damage to the wall.

• There should not be any heat source or steam

near the unit.

• There should not be any obstacles to prevent

the air circulation.

• A place where air circulation in the room will

be good.

• A place where drainage can be easily

obtained.

• A place where noise prevention is taken into

consideration.

• Do not install the unit near the door way.
• Ensure the spaces indicated by arrows from

the wall, ceiling, or other obstacles.

• Take the air conditioner weight into account and

select a place where noise and vibration are
minimum.

• Select a place so that the warm air and noise

from the air conditioner do not disturb neighbors.

• Place that can sufficiently endure the weight

and vibration of the outdoor unit and where
even installation is possible.

• Place that has no direct influence of snow or rain
• Place with no danger of snowfall or icicle drop
• Place without weak floor or base such as

decrepit part of the building or with a lot of snow
accumulation

2. Outdoor unit

• If an awning is built over the unit to prevent direct sunlight or rain exposure, make sure that heat

radiation from the condenser is not restricted.

• Ensure that the spaces indicated by arrows around front, back and side of the unit.
• Do not place animals and plants in the path of the warm air.

More than

20cm

More than eye-level

More than

20cm

More than

20cm

More than

20cm

(Ceiling installation)

(Floor/Wall installation)

More than 20cm

More than 5cm

More than 20cm

More than 5cm

More than 20cm

More than
30cm

More than 30cm

More
than 60cm

More than 60cm

More than
70cm

1,MFL67855401,영영 2017. 6. 29. 영영 1:50 Page 8

Summary of Contents for UU09W ULD


















































Search results

Summary of Contents for UU09W ULD

Reviews:

Related manuals for UU09W ULD

Brands by name

Popular brands

LG UU09W ULD, Installation Manual

Search results

Summary of Contents for UU09W ULD

Reviews:

Related manuals for UU09W ULD

Brands by name

Popular brands