LG UU09W ULD Installation Manual Download Page 7

Page: 7 / 49

Installation of Indoor, Outdoor Unit

Installation Manual

ENGLISH

Installation of Indoor, Outdoor Unit

1. Indoor unit

Cassette type

• There should not be any heat source or steam

near the unit.

• There should not be any obstacles to prevent

the air circulation.

• A place where air circulation in the room will

be good.

• A place where drainage can be easily obtained.
• A place where noise prevention is taken into

consideration.

• Do not install the unit near the door way.
• Ensure the spaces indicated by arrows from

the wall, ceiling, or other obstacles.

• The indoor unit must keep the maintenance

space.

Duct type

• The place shall easily bear a load exceeding

four times the indoor unit’s weight.

• The place shall be able to inspect the unit as

shown the figure.

• The place where the unit shall be leveled.
• The place shall allow easy water

drainage.(Suitable dimension “H” is necessary
to get a slope to drain as figure.)

• The place shall easily connect with the

outdoor unit.

• The place where the unit is not affected by an

electrical noise.

• The place where air circulation in the room will

be good .

• There should not be any heat source or steam

near the unit

You need to select adequate installation location considering the following conditions, and make
sure to acquire the consent of the user.

Selection of the best location

Unit:cm

Ceiling

Ceiling Board

30 or more

Above 250

330 or less

100

or more

50 or

30 or less

Floor

600

Top view

(unit: mm)

Front view

Front

Inspection hole

(600X600)

Control box

1000

1,MFL67855401,영영 2017. 6. 29. 영영 1:50 Page 7

Summary of Contents for UU09W ULD


















































Search results

Summary of Contents for UU09W ULD

Reviews:

Related manuals for UU09W ULD

Brands by name

Popular brands

LG UU09W ULD, Installation Manual

Search results

Summary of Contents for UU09W ULD

Reviews:

Related manuals for UU09W ULD

Brands by name

Popular brands