LG MFL40910614 Installation Manual Download

Page: 31 / 35

Installation Manual

ENGLISH

Test running

Function Code

Set

Keep pressing button setting for 4
secs to enter installer setting mode until
code displayed in timer segment.

Press button to start.

1. Cassette type

After installing the product, you must run a Test Run mode.

For details related to this operation, refer to the product manual.

Installer Setting -Test Run Mode

❊

18˚C cooling, High Fan Speed, Airflow direction mode will be operated during 18 minutes with ignoring
room temperature.

❊

After running 18 minutes under test run mode, system will automatically turn OFF.

❊

In case of duct type, the Airflow UP/DOWN function is not displayed.

❊

During test run mode, receiving signal from wireless remote controller will release this operation.
If you press any kind of button, Test Run mode will be released.

Floor Standing type

Push the temperature low key and On/Off
Key For over 3 sec simultaneously indoor
side

FAN

SPEED

OFF

MODE

Summary of Contents for MFL40910614




































Search results

Summary of Contents for MFL40910614

Reviews:

Related manuals for MFL40910614

Brands by name

Popular brands

LG MFL40910614, Installation Manual

Search results

Summary of Contents for MFL40910614

Reviews:

Related manuals for MFL40910614

Brands by name

Popular brands