LG LSN5MR3T1 Installation Manual Download Page 1 | Manualshive

Page: 1 / 22

background image

INSTALLATION MANUAL

AIR CONDITIONER

TYPE : WALL MOUNTED

Please read this installation manual completely before installing the product.
When the power cord is damaged, replacement work shall be
performed by authorized personnel on;y.
Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
Please retain this installation manual for
future reference after reading it thoroughly.

P/No. MFL39754859

LG Electronics India Pvt. Ltd.

Registered Office

:

A-27, Mohan Co-operative

Industrial Estate, Mathura Road, New Delhi-110044
Tel: 011-26991412, Fax: 011-26991410

www.lg.com

1
2
3
...
»

Summary of Contents for LSN5MR3T1























Reviews:

No comments

Related manuals for LSN5MR3T1

Brand: Daikin Pages: 108

Brand: Daikin Pages: 40

Brand: Daikin Pages: 344

Clima-Flex CLIV Series

Brand: Daikin Pages: 46

Brand: GUTFELS Pages: 66

Brand: F&U Pages: 15

Brand: Trotec Pages: 6

Brand: Thermoscreens Pages: 38

Brand: York Pages: 20

Brand: Prem-I-Air Pages: 15

Brand: Zamil Pages: 51

Brand: Evolar Pages: 49

Brand: Vaillant Pages: 16

Brand: Impecca Pages: 40

activair SAC16870N

Brand: Swann Pages: 20

Brand: Daikin Pages: 273

Pro-Kool M-PROK142

Brand: Schaefer Pages: 16

Mini Amazon III

Brand: Kaysun Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands