LG LP073CD2A Manual Download Page 36

Page: 36 / 51

- 36 -

LGE Internal Use Only

208/230 Volt Units

1. Remove and discard the white lead from the wire

assembly.

2. Connect the black lead to the line 2 terminal on the control

board.

3. Connect the red lead to the common (C) terminal on the

capacitor.

4. Connect the ground wire to the partition panel where the

ground wire on the power cord was located.
Use the supplied green ground screw.

5. Connect the red lead in the wire assembly at the junction

box to the red lead of the field power source.

6. Connect the black lead in the wire assembly at the junction

box to the black lead of the field power source.

7. Connect the ground wire of the field power source to the

ground wire of the wire assembly at the junction box.

8. Install the junction box cover plate.

9. Reinstall the control panel assembly.

265 Volt Units

1. Remove and discard the red lead from the wire assembly .

2. Connect the black lead to the center terminal of the fuse

holder.

3. Connect the white lead to the common (C) terminal on the

capacitor.

4. Connect the ground wire to the partition panel where the

ground wire on the power cord was located.
Use the supplied green ground screw.

5. Connect the white lead of the wire assembly at the junction

box to the white lead of the field power source.

6. Connect the black lead of the wire assembly at the junction

box to the black lead of the field power source.

7. Connect the ground wire of the field power supply to the

bare ground wire of the wire assembly at the junction box.

8. Install the junction box cover plate.

9. Reinstall the control panel assembly.

Wall Sleeve

Cover plate

Control Panel

Base Pan

Bracket

Right Side of Chassis

3/16"

Diamenter Hole

Back of Control Panel

Electrical Supply Wires

Ground Wie

with Eyelet

Terminal

Power Leads
with Push on

Connectors

Metal Box

with Straight Clamp

Conduit

28" Max

Wire Tie

Figure 47 - Electrical Wiring Routing

Figure 46 - Metal Box Location

Figure 45 - Mounting Hard Wire Junction Box Kit

Summary of Contents for LP073CD2A



















































Search results

Summary of Contents for LP073CD2A

Reviews:

Related manuals for LP073CD2A

Brands by name

Popular brands

LG LP073CD2A, Manual

Search results

Summary of Contents for LP073CD2A

Reviews:

Related manuals for LP073CD2A

Brands by name

Popular brands