LG LG A1C-V5 Series Installation Manual Download Page 96

Page: 96 / 108

Electronics

AC Module System Installation Manual

Rev. 1.0

Cause

Device

Event Code

Impact

Event Name

(App / Web)

Event

Class

Description

Remarks

MI_VDC_OVR

Error

Inverter

Failure Error

Vdc

Status

ERROR. Iac Status - 1:

Vdc Over (Error #4

DC Link Voltage High)

AC Module has been in failure

mode.

MI_VFR_OVR

Notice AC Frequency

High

Vfreq

Status

NOTICE. Vfreq

Status 10: Vfreq Over

AC Frequency is the

frequency at which voltage

varies on the utility grid. AC

Frequency coming from the

utility is higher than allowed.

These events are usually

transient and recovered

by the utility. No action is

required unless the condition

persists.

MI_VFR_UND

Notice AC Frequency

Low

Vfreq

Status

NOTICE. Vfreq Status

11: Vfreq Under

AC Frequency is the

frequency at which voltage

varies on the utility grid. AC

Frequency coming from the

utility is lower than allowed.

These events are usually

transient and recovered

by the utility. No action is

required unless the condition

persists.

MI_VPV_OVR

Error

DC Voltage

High

Vpv

Status

ERROR. Vpv

Status -10: Vpv Over

(Error #1 - DC Voltage

Too High)

DC Input voltage from the AC

Module is higher than

allowed.

MI_VPV_UND

Notice

DC Voltage

Low

Vpv

Status

NOTICE. Vpv

Status -11: Vpv Under

(Error#7 - DC Voltage

Too Low)

DC Input voltage from the

AC Module is too low. This

is usually a normal condition

during hours of low light

and at dawn and dusk. If this

condition does happen during

hours of full daylight, the

AC Module may be heavily

shaded or covered by snow.

Summary of Contents for LG A1C-V5 Series












































































































Search results

Summary of Contents for LG A1C-V5 Series

Reviews:

Related manuals for LG A1C-V5 Series

Brands by name

Popular brands

LG LG A1C-V5 Series, Installation Manual

Search results

Summary of Contents for LG A1C-V5 Series

Reviews:

Related manuals for LG A1C-V5 Series

Brands by name

Popular brands