LG L5UC728FA2 Installation Manual Download Page 18

Page: 18 / 60

Multi Type Air Conditioner

Installation of Indoor, Outdoor Unit

Insulate the joint and tubes completely.

All thermal insulation must comply with local requirement.

REFRIGERANT PIPE

• Insulate and tape the gas piping.

■

After all workings are finished, check the working and operation.

• Air distribution

Is the air circulation good?

• Drain

Is the drainage smooth and no sweating?

• Gas leakage

Is the piping connection correct?

• Wiring

Is the wiring connection correct?

• Lock-bolt

Is the lock-bolt of compressor loosened?

THERMAL INSULATION

TEST AND CHECK

Make sure that there is no clearance here.

Overlap with thermal
insulator for piping.

Thermal insulator for refrigerant pipe
(Local supply)

Thermal insulator for
piping(Local supply)

Hose clip for thermal insulator(Local supply)

Union for liquid pipe

Refrigerant pipe and thermal
insulator(Local supply)

Union for gas pipe

Thermal insulator for refrigerant pipe
(Local supply)

Hose clip for thermal insulator
(Local supply)

Power cable

Thermal insulator

Gas pipe

Liquid pipe

Tape

Insulation, others

Summary of Contents for L5UC728FA2





























































Search results

Summary of Contents for L5UC728FA2

Reviews:

Related manuals for L5UC728FA2

Brands by name

Popular brands

LG L5UC728FA2, Installation Manual

Search results

Summary of Contents for L5UC728FA2

Reviews:

Related manuals for L5UC728FA2

Brands by name

Popular brands