LG GM210 Service Manual Download Page 45

Page: 45 / 165

- 46 -

LGE Internal Use Only

Only for training and service purposes

3. TECHNICAL BRIEF

LGE Internal Use Only

3.13 Audio Interface

Figure 3-13-1 ABB Internal Audio Block Diagram

The AD6725 Audio Section supports communications and personal audio applications. The Audio Section

provides an audio codec with two digital-to-analog converters and an analog-to-digital converter, a

microphone interface, and analog input and output channels.

Audio and Music Serial Ports

The AD6725 Audio Serial Port is described in detail in the Audio Serial Port (ASPORT) section below.

AD6725 Music serial port (MSPORT) is described in detail in the Music Serial Port (MSPORT) section below.

Audio Codec

The AD6725 audio codec supports communications applications with digital sample rates of 8 kHz or

16kHz. DAC 1 is used for receiving speech. An ADC is used for sending speech. The AD6725 audio codec

supports personal audio applications with digital sample rates of 8 kHz, 11.025kHz, 12 kHz, 16 kHz, 22.05

kHz, 24 kHz, 32 kHz, 44.1 kHz, or 48 kHz. DAC 1 and DAC 2 are used for monophonic audio. The channels

are common in the digital section. DAC 1 and DAC 2 are used together for stereo audio, with DAC 1

decoding the left-channel digital input and DAC 2 decoding the right-channel digital input.

Summary of Contents for GM210
































































































































































Search results

Summary of Contents for GM210

Reviews:

LG GM210, Service Manual, Page: 45 / 165

Search results

Summary of Contents for GM210

Reviews: